Toro 03113SL Rev E Greensmaster 3150 Service Manual

Backlapping (Units with Optional Backlap/Variable Reel Speed Kit)
DANGER
2
CLOCKWISE
1
TO AVOID PERSONAL INJURY OR DEATH:
D
Never place  hands or  feet in  the reel  area
3
while the engine is running.
While backlapping,  the reels may  stall and
then restart.
4
D
D
foot.
D
running.
Do not  attempt to  restart reels  by hand or
Do not adjust reels while the engine is
D
attempting to clear the reel.
If a reel stalls, stop engine before
D
one motor moves the other two.
Reel motors are connected in series, moving
Figure 11
1.
2.
Directional valve knob
Ball switch
3.
4.
Flow control valve knob
Hydraulic manifold
1.
Position machine on a clean and level surface, low-
er cutting units, stop engine, engage parking brake, and
remove key from the ignition switch.
9.
To make  an adjustment to  the cutting units  while
backlapping,  turn reels  OFF  by  moving the  RAISE/
LOWER--MOW control to the RAISE position. Shut off
engine. After the adjustments have been completed, re-
peat steps 4 through 6.
2.
position.
MovefunctionalcontrollevertotheNeutral/Backlap
IMPORTANT: Do not attempt to rotate the direction-
al valve knob  when the machine  or reels are run-
ning.
10. When the backlap operation is completed, shut off
engine and rotate directional valve knob counter--clock-
wisefully(90ofromthebacklapposition)toforwardposi-
tion. Also, rotate flow control valve knob to position 13
for height--of--cut settings of a 1/4 inch or below.
3.
Raise seat  and rotate directional valve  knob fully
clockwise to the backlap position.
4.
5.
justments appropriate for backlapping (see Bedknife to
Reel Adjustment in Cutting Unit Operator’s Manual).
Rotate flow control valve knob to position 6.
Note:
on the decal that is located on the underside of the seat
support.
For additional settings, refer to the instructions
On all cutting units, make initial reel to bedknife ad-
11.  Wash all lapping compound off the cutting units.
6.
forward to start the reels.
Start engine and move Raise / Lower -- Mow control
12. For a better cutting edge, run a file across the front
face of the bedknife when the lapping operation is com-
pleted. This will remove any burrs or rough edges that
may have built up on the cutting edge.
7.
8.
Rotate flow control valve knob to position 1.
Apply lapping compound with a long handled brush
Note:
Additional   instructions  and   procedures   on
(see Special Tools).
backlapping are available in the Toro General  Service
Training Book, Reel Mower Basics (part no. 09168SL).
CAUTION
Be careful  when backlapping the  reel because
contact with the reel or other moving parts  can
result in personal injury.
Greensmaster 3150
Page 10 - 9 Rev. E
Dual Point Adjust Cutting Units
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 306 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(1 votes, average: 2 out of 2)
Lawn and Garden readers have rated Toro 03113SL Rev E Greensmaster 3150 Service Manual 2.0 out of 2.0 based on 1 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 03113SL Rev E Greensmaster 3150 Service Manual SKU UPC Model
kurt on May 29, 2014.

Safety switches not working


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website