Toro 03113SL Rev E Greensmaster 3150 Service Manual

Procedure for  Traction Drive  Hydrostat (P3) Flow
Test:
Note:
See Adjusting the Transport Speed in the traction unit
Operator’s Manual for additional information.
Makesuretransportspeedisproperlyadjusted.
This test measures hydrostat pump output (flow). Dur-
ing this test, pump load is created atthe flowmeter using
the adjustable load valve on the tester.
10. Slowly close flow control valve until pressure gauge
reads 1000 PSI (69 bar).
1.
perature by operating the machine for approximately 10
minutes.
Make sure hydraulic oil is at normal operating tem-
11.  Observeflowgauge.TESTERREADINGshouldbe
a minimum flow of 13.3 GPM. Record test results.
12.
Releasetractionpedal,opencontrolvalveontester,
2.
units lowered  and off. Make sure  engine is off.  Make
sure the hydraulic tank is full.
Park machine  on a level  surface with  the cutting
and turn off engine.
13.
If specifications are not met consider the following:
A.  The traction  pedal and/or traction  speed may
need adjustment (see the Traction Unit Operator’s
Manual).
CAUTION
B.  The hydrostat needs to be repaired or replaced
as necessary.
Before continuing further, read and  become fa-
miliar with Precautions for Hydraulic Testing.
C. Makenecessary  repairsbeforeperformingaddi-
tional tests.
3.
tral position (see the Traction Unit Operator’s manual).
Make sure the transmission is adjusted to the neu-
14.
If specifications  are met, check  wheel motor  effi-
ciency (see Wheel Motor Efficiency Testinthischapter).
4.
Block  up front  wheels  off the  ground  (also rear
wheel if machine is equipped  with 3WD) to allow flow
through the traction circuit.
15. If  testing is  complete, disconnect  tester from hy-
draulic tube and hose. Reconnect hose to tube.
5.
Disconnect hydraulic hose from the hydraulic tube
that connects to the upper hydraulic fitting on the front
side of the hydrostat (Fig. 19).
4
1
6.
Install tester in series with the pump and the discon-
nected hose.  Make sure  flow control valve  on the
tester is fully open.
7.
Make sure functional lever is in the transport posi-
tion.
8.
50
Start engine and move throttle to full speed (2850 +
RPM) position.
CAUTION
FRONT
2
3
Use extreme  caution when  taking gauge read-
ings. The front tire on the ground will be trying to
move the machine forward.
Figure 19
1.
2.
Hydrostat
Upper fitting
3.
4.
Hydraulic tube
Hydraulic hose
9.
tion.
Slowly push traction  pedal into fully forward posi-
Greensmaster 3150
Page 4 -- 31
Hydraulic System (Rev. E)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 306 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(1 votes, average: 2 out of 2)
Lawn and Garden readers have rated Toro 03113SL Rev E Greensmaster 3150 Service Manual 2.0 out of 2.0 based on 1 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 03113SL Rev E Greensmaster 3150 Service Manual SKU UPC Model
kurt on May 29, 2014.

Safety switches not working


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website