Toro 08162SL Model 30413 Groundsmaster 4100 D Service Manual

Removal (Fig 49)
Park machine on a level surface, lower cutting deck,
stop engine,  engage parking  brake  and remove  key
from the ignition switch.
Installation (Fig 49)
1.
1.  Lubricate new O--rings with clean hydraulic  oil and
position on pump.
2.
Slide coupler onto the piston pump output shaft.
2.
to gear pump.
Raise seat and secure it with prop rod to gain access
3.
Position O--rings  and spacer  to gear  pump. Align
gear teeth and slide gear pump input shaft into coupler.
Secure gear  pump  to piston  pump with  two  (2) cap
screws and washers. Torque cap screws from 79 to 84
ft--lb (108 to 113 N--m).
3.
4.
pump removal, thoroughly clean exterior of  pump and
fittings.
Drain the hydraulic reservoir.
To prevent contamination of hydraulic system during
4.  Remove caps or plugs from  hydraulic lines and fit-
tings. Install hydraulic lines to gear pump.
5.
Read the  General Precautions  for Removing  and
Installing Hydraulic System Components at the begin-
ning of this section.
5.  Replace hydraulic  filter and  fill hydraulic reservoir
with new hydraulic oil.
6.
caps or plugs on open hydraulic lines and fittings. Label
disconnected hydraulic lines for proper installation.
Disconnect hydraulic lines from gear pump and put
6.  Disconnect engine run solenoid electrical connector
to prevent  engine  from starting.  Prime the  hydraulic
pumpbyturningtheignitionkeyswitchtostartandcrank
theengineforten(10)seconds.Wait15secondsandre-
peat cranking procedure again.
7.
ling.
Support gear pump assembly to prevent it from fal-
7.
start the engine and check for proper operation.
Connect engine  run solenoid  electrical connector,
8.
Removetwo(2)capscrewsandwashersthatsecure
gear pump to piston  pump. Remove gear pump, cou-
pler, spacer and O--rings from machine through the seat
opening.
8.  Properly fill hydraulic system (see Charge Hydraulic
System in this section).
9.
Stop engine and check for hydraulic oil leaks. Check
hydraulic reservoir oil level.
Groundsmaster 4100--D
Page 4 -- 69
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 298 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

One thought on “Toro 08162SL Model 30413 Groundsmaster 4100 D Service Manual

  1. At only 700mm wide the Mini Dumper is even at home on tight access
    sites. No need to grunt, groan, and force the
    mower about the yard. The US will be getting a revised 2011 Jeep Wrangler but the diesel option will not be offered in the United States.

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website