Blade Spindle Service
DRIVEN SPINDLE
7
8
1
2
3
9
10
12
11
14
130
(176
to 150 ft--lb
to 203 N--m)
4
13
DRIVE SPINDLE
15
1
5
2
9
8
16
17
6
4
Figure 16
1.
2.
3.
4.
5.
6.
Lock nut
7.
8.
9.
10. Outer bearing spacer
11. Inner bearing spacer
12. Spacer ring
O--ring
Oil seal
Bearing cup and cone
13. Snap ring
Flat washer
14. Grease fitting
15. Spindle housing
16. Spindle shaft spacer
17. Spindle shaft
Driven pulley
Spindle shaft
Drive pulley (single shown)
Hydraulic motor mount
Disassembly (Fig. 16)
Loosen and remove lock nut from top of spindle
shaft. Remove hardened washer and pulley from
spindle. For drive spindle, remove hydraulic motor
mount.
Assembly (Fig. 16)
1.
NOTE: Areplacement spindle bearing set contains two
(2) bearings, a spacer ring and a large snap ring (items
1, 2 and 3 in Fig. 17). These parts cannot be purchased
separately. Also, do not mix bearing set components
from one deck spindle to another.
2.
Remove the spindle shaft from the spindle housing
whichmayrequiretheuseofanarborpress.Thespindle
shaft spacer should remain on the spindle shaft as the
shaft is being removed.
NOTE: A replacement bearing spacer set includes the
inner spacer and outer spacer (items 4 and 5 in Fig. 17).
Do not mix bearing spacers from one deck spindle to
another.
3.
Carefully remove oil seals from spindle housing tak-
ing care to not damage seal bore in housing.
IMPORTANT: If new bearings are installed into a
usedspindlehousing,itmaynotbenecessarytore-
place the original large snap ring. If the original
snap ring is in good condition with no evidence of
damage (e.g. spun bearing), leave the snap ring in
the housing and discard the snap ring that comes
with the new bearings. Ifthe large snap ring isfound
to be damaged, replace the snap ring.
4.
spacer ring to drop out of the spindle housing (Fig. 17).
Allow the bearing cones, inner bearing spacer and
5.
cups and the outer bearing spacer from the housing.
Using an arbor press, remove both of the bearing
6.
The large snap ring can remain inside the spindle
housing. Removal of this snap ring is very difficult.
1.
Iflargesnapringwasremovedfromspindlehousing,
install snap ring into housing groove. Make sure snap
ring is fully seated in housing groove.
Cutting Deck
Page 8 -- 18
Groundsmaster 4100--D
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 30413, Toro Groundsmaster Groundsmaster 4100 D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)
At only 700mm wide the Mini Dumper is even at home on tight access
sites. No need to grunt, groan, and force the
mower about the yard. The US will be getting a revised 2011 Jeep Wrangler but the diesel option will not be offered in the United States.