8.
Remove and discard back--upgaskets and pressure
seals from wear plates.
3
9.
Turn front flange over, with seal side up.
2
IMPORTANT: Make sure not to damage the front
flange counter bore when removing the seals from
the front flange.
10.Carefully
remove dust seal, retaining ring, flange
washer and shaft seal from the front flange (Fig. 74).
Discard seals.
1
Inspection
4
1.
emery cloth.
Remove any nicks and burrs from all parts with
Figure 73
3.
4.
1.
2.
Gear shaft spline
Gear shaft
Gear teeth
Gear face edge
CAUTION
2
3
1
4
Use eye protection such as goggles when using
compressed air.
2.
Clean all parts with solvent. Dry all parts with com-
pressed air.
3.
Inspect drive gears and idler gears for the following
(Fig. 73):
Figure 74
A. Gear shafts should be free of rough surfaces and
1.
Dust seal
3.
4.
Flange washer
Shaft seal
2.
Retaining ring
excessive wear at bushing points and sealing areas.
Scoring, rough surfaces or wear on gear shafts indi-
cates need for replacement.
Assembly (Fig. 71)
NOTE: When assembling the motor, check the marker
line on each part to make sure the parts are properly
aligned during assembly.
B. Gear teeth should be free of excessive scoring
and wear. Any broken or nicked gear teeth must be
replaced.
1.
Lubricate O--rings,pressure seals, back--upgaskets
C. Inspect gear face edge for sharpness. Sharp
edges of gears will mill into wear plates and, thus,
must be replaced.
and wear plate grooves with a thin coat of petroleum jel-
ly. Lubricate all other internal parts freely with clean hy-
draulic oil.
4.
Inspect wear plates for the following:
2.
Install new seals into front flange (Fig. 74):
A. Bearingareasshouldnothaveexcessive wearor
scoring.
A. Press shaft seal into front flange until it reaches
the bottom of the bore.
B. Face of wear plates that are in contact with gears
should be free of wear, roughness or scoring.
B. Install flange washer into front flange and then
install retaining ring into the groove of the front
flange.
C. Thickness of wear plates should be equal.
5.
Inspect front flange and rear cover for damage or
C. Install new dust seal into front flange.
wear.
3.
Place front flange, seal side down, on a flat surface.
Groundsmaster 4100--D
Page 4 -- 105
Hydraulic System
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 30413, Toro Groundsmaster Groundsmaster 4100 D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)
At only 700mm wide the Mini Dumper is even at home on tight access
sites. No need to grunt, groan, and force the
mower about the yard. The US will be getting a revised 2011 Jeep Wrangler but the diesel option will not be offered in the United States.