Battery Service
The battery is the heart of the electrical system. With
regular andproper service, battery lifecan beextended.
Additionally, battery and electrical component failure
can be prevented.
2
CAUTION
1
When working with batteries, use extreme cau-
tion to avoid splashing or spilling electrolyte.
Electrolyte can destroy clothing and burn skin or
eyes. Always wear safety goggles and a face
shield when working with batteries.
3
Electrolyte Specific Gravity
Fully charged: 1.265 corrected to 80oF (26.7oC)
Discharged: less than 1.240
Figure 60
1.
2.
Negative (--) cable
Positive (+) cable
3.
Battery strap
Battery Specifications
BCI Group Size 24
650
CCA at 0o F (--17.8o C)
Reserve Capacity of 110 minutes at 80oF (26.7oC)
Battery Inspection, Maintenance and Testing
Dimensions (including terminal posts and caps)
1.
Perform following inspections and maintenance:
Length
Width
Height
10.2 inches (259 mm)
6.6 inches (167 mm)
9.0 inches (228 mm)
A. Check for cracks. Replace battery if cracked or
leaking.
Battery Removal and Installation (Fig. 60)
B. Check battery terminal posts for corrosion. Use
wire brush to clean corrosion from posts.
1.
access panel.
Raise and support operator seat. Remove battery
IMPORTANT: Before cleaning the battery, tape
or block vent holes to the filler caps and make
sure the caps are on tightly.
2.
ter negative cable is removed, loosen and remove posi-
tive cable.
Loosen and remove negative cable from battery. Af-
C. Check for signs of wetness or leakage on the top
ofthe battery which mightindicate aloose ormissing
filler cap, overcharging, loose terminal post or over-
filling. Also, check battery case for dirt and oil. Clean
the battery with a solution of baking soda and water,
then rinse it with clean water.
3.
chine.
Loosen battery strap that secures battery to ma-
4.
Carefully remove battery from machine.
5.
Install battery in reverse order making sure to con-
nect and tighten positive cable to battery before con-
necting negative cable.
D. Check thatthe cover seal is notbroken away.Re-
place the battery if the seal is broken or leaking.
NOTE: Before connecting the negative (ground) cable
to the battery, connect a digital multimeter (set to DC
Amps) between the negative battery post and the nega-
tive (ground) cable connector. The reading should be
less than 0.1 amp. If the reading is 0.1 amp or more, the
machine’s electrical system should be tested for short
circuits or faulty components and repaired.
E. Check theelectrolyte levelineachcell.Ifthelevel
is below the tops of the plates in any cell, fill all cells
withdistilledwaterbetween theminimumandmaxi-
mum fill lines. Charge at 15 to 25 amps for 15 min-
utes to allow sufficient mixing of the electrolyte.
6.
cess panel. Lower and secure operator seat.
Secure battery with battery strap. Install battery ac-
Electrical System
Page 5 -- 38
Groundsmaster 4100--D
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 30413, Toro Groundsmaster Groundsmaster 4100 D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)
At only 700mm wide the Mini Dumper is even at home on tight access
sites. No need to grunt, groan, and force the
mower about the yard. The US will be getting a revised 2011 Jeep Wrangler but the diesel option will not be offered in the United States.