Toro 08162SL Model 30413 Groundsmaster 4100 D Service Manual

Removal (Fig. 67)
Park machine on a level surface, lower cutting deck,
Installation (Fig. 67)
1.
1.  If removed, install ball joints into steering cylinder.
stop engine,  engage parking  brake  and remove  key
from the ignition switch.
2.
If fittings were removed from steering cylinder, lubri-
cate and place new O--rings onto fittings. Install fittings
intoportopeningsusingmarksmadeduringtheremoval
process  to properly  orientate fittings.  Tighten fittings
(see Hydraulic Fitting Installation in  the General Infor-
mation section of this chapter).
2.
Installing Hydraulic System Components at the begin-
ning of this section.
Read the  General Precautions  for Removing  and
3.
To prevent contamination of hydraulic system during
steering cylinder removal, thoroughly clean exterior of
cylinder and fittings.
3.  Slide ram end ball joint through holeon steering arm.
Secure with axle washer and hex slotted nut. Slide fixed
end of cylinder through hole on axle. Secure with slotted
hexnut.Torqueslottedhexnutsto100ft--lbs(135N--m)
and then continue tightening thenutuntilhex nutgroove
aligns with cotter pin hole in ball joint. Install cotter pin
to nut and ball joint.
NOTE:  Toeaseinstallation,labelthehydraulichosesto
show their correct position on the steering cylinder.
4.
5.
andballjointspacerfromthethreaded    endsofballjoints
(Fig. 67). Remove steering cylinder with ball joints from
machine.
Remove hydraulic hoses from steering cylinder.
Remove cotter pins, hex  slotted nuts, axle washer
4.
5.
6.
Install hydraulic hoses to steering cylinder.
Fill reservoir with hydraulic fluid as required.
After assembly is completed, operate steering cylin-
dertoverifythathydraulichosesandfittingsarenotcon-
tacted by anything.
6.
cylinder, mark fitting orientation to allow correct assem-
bly. Remove fittings from cylinder and discard O--rings.
If hydraulic fittings are to be removed from steering
7.
If needed, remove ball joints from steering cylinder.
Groundsmaster 4100--D
Page 4 -- 99
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 298 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

One thought on “Toro 08162SL Model 30413 Groundsmaster 4100 D Service Manual

  1. At only 700mm wide the Mini Dumper is even at home on tight access
    sites. No need to grunt, groan, and force the
    mower about the yard. The US will be getting a revised 2011 Jeep Wrangler but the diesel option will not be offered in the United States.

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website