Removal (Fig. 91)
Park machine on a level surface, lower cutting deck,
stop engine, engage parking brake and remove key
from the ignition switch.
Installation (Fig. 91)
1.
1. If removed, install spherical bearings into lift cylinder
clevis ends.
A. On shaft clevis, press spherical bearing into cle-
vis and secure with retaining ring.
2.
Read the General Precautions for Removing and
Installing Hydraulic System Components at the begin-
ning of this section.
B. On barrel clevis, install spherical bearing on ta-
pered stud and secure with flange nut. Torqueflange
nut from 30 to 40 in--lb (41 to 54 N--m). Install stud
with spherical bearing into clevis and secure with re-
taining ring.
3.
Remove deck covers as needed to allow access to
lift cylinder hoses and fasteners.
4.
To prevent contamination of hydraulic system during
lift cylinder removal, thoroughly clean exterior of cylin-
der and fittings.
2. Thoroughly clean tapered surfaces of lift cylinder
stud and mounting boss on deck.
NOTE: Toeaseinstallation,labelthehydraulichosesto
show their correct position on the lift cylinder.
3. Position lift cylinder to cutting deck. Insert tapered
stud into deck mounting boss. Secure stud with flat
washer and lock nut. Torque flange nut from 160 to 180
ft--lb (217 to 244 N--m).
5.
Disconnect hydraulic hoses from lift cylinder.
6.
cylinder clevis to the wing deck.
Remove cap screw and lock nut that secure the lift
4.
Insert cap screw from the front of the deck through
the deck brackets and cylinder shaft clevis. Secure cap
screw with lock nut. Torque lock nut from 160 to 180 ft--
lb (217 to 244 N--m).
7.
stud on the barrel end of the lift cylinder.
Remove lock nut and flat washer from the tapered
5.
6.
7.
8.
Attach hydraulic hoses to lift cylinder.
8.
Remove lift cylinder from deck assembly.
Install any removed deck covers.
9.
ends, if required.
Remove spherical bearings from lift cylinder clevis
Fill reservoir with hydraulic fluid as required.
After assembly is completed, operate lift cylinder to
A. On shaft clevis, remove retaining ring and then
press spherical bearing from clevis.
verify that hydraulic hoses and fittings are not contacted
by anything.
B. On barrel clevis, remove retaining ring and then
press tapered stud with spherical bearing and flange
nut from clevis. Remove flange nut and then spheri-
cal bearing from stud.
Groundsmaster 4100--D
Page 4 -- 131
Hydraulic System
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 30413, Toro Groundsmaster Groundsmaster 4100 D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)
At only 700mm wide the Mini Dumper is even at home on tight access
sites. No need to grunt, groan, and force the
mower about the yard. The US will be getting a revised 2011 Jeep Wrangler but the diesel option will not be offered in the United States.