4.
brackets.
Position upper end of links to center cutting deck
11.Lower wing deck and inspect deck latch assembly to
insure that front link is locked when the wing deck is in
the lowered position. There should be agap from 0.060”
to 0.090” (1.5 to2.2 mm)between thearm latchactuator
and the latch pivot (Fig. 8). If gap is incorrect, adjust link
position by repositioning the location of the hardened
spacers (item 42) and thrust washers (item 6). At a mini-
mum, there must be a hardened spacer positioned to
the rear of the front link.
5.
deck.Whileinstalling pivot pins to center deck andlinks,
insert spacers and washers as follows:
Alignupperendoflinkswithmountingholesincenter
A. Place a hardened spacer (item 42) on each side
of the front link. Use one or two thrust washers on
rear side of assembly so that link is snug between
deck brackets.
12.Lubricate
ponents.
grease fittings on cutting deckand liftcom-
B. Place a thrust washer (item 6) on each side of
rear link.
13.Check
distance between inner deck blade on wing
deck and outer deck blade on center deck. Distance be-
tween blades should be 0.380” to 0.620” (9.7 to 15.7
mm) (Fig. 9). If blade distance is incorrect, loosen hex
jam nut (item 32) on rear link assembly and adjust cap
screw (item 31). Tighten jam nut when blade distance is
correct.
6.
screw.
Secure pins with carriage screw and flange head
7.
Cap screw on rear link uses a flat washer (item 28). Cap
screw on front link also secures hose guide (item 38).
Install cap screw (item 29) to pivot pin on both links.
14.Check
if necessary (see Wing Deck Position Switches in the
Adjustments section of Chapter 5 -- Electrical System).
operation ofwing deck position switch. Adjust
8.
cylinder with cap screw and lock nut.
Position lift cylinder to the wing deck (Fig. 7). Secure
9.
Deck Motor Installation in the Service and Repairs Sec-
tion of Chapter 4 -- Hydraulic System).
Install hydraulic motor to cutting deck (see Cutting
15.Secure
switch shield (item 50) to center deck.
10.Fully
raise wing deck, stop engine and remove key
from the ignition switch. Secure flex shield to wing deck
with shield strap and three (3) washer head screws.
Lower wing deck.
Cutting Deck
Page 8 -- 12
Groundsmaster 4100--D
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 30413, Toro Groundsmaster Groundsmaster 4100 D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)
At only 700mm wide the Mini Dumper is even at home on tight access
sites. No need to grunt, groan, and force the
mower about the yard. The US will be getting a revised 2011 Jeep Wrangler but the diesel option will not be offered in the United States.