Toro 08162SL Model 30413 Groundsmaster 4100 D Service Manual

Differential Gear Installation
If the ring gear was removed, use medium strength
3
1.
2
thread  locking  compound and  tighten  the  mounting
screws from 22 to 25 ft-lb (30 to 34 N--m).
1
2.
andbearingsurfacesofthedifferentialpiniongears,pin-
ion washers and side gears.
Apply molybdenum disulfide  grease to the  splines
3.
original location in the differential case.
Install the side  gear shims and  side gears in their
4.
ers in their original location in the differential case. Tem-
porarily install the differential pinion shaft.
Place the differential pinion gears and pinion wash-
Figure 39
1.
2.
Vise
3.
Dial indicator
5.
indicator at the tooths center and measure the differen-
tial pinion gear to side gear backlash (Fig. 39).
Secure the differential case in a vise. Position a dial
Differential gear case
More than 35% total tooth contact
PINION GEAR TO SIDE GEAR BACKLASH:
0.004
to 0.016 in. (0.10 to 0.40 mm)
6.
Adjust backlash by increasing or reducing side gear
shim thickness.
NOTE:  Side gear shims are available in 0.043 in. (1.1
mm), 0.047 in. (1.2 mm) and 0.051 in. (1.3 mm) thick-
ness.
1/3
from small end of tooth
to 1/2 of entire width
Figure 40
7.
Steel Blue lightly over several gear teeth.
Apply gear marking  compound, such as  DyKemR
12.Install differential  gear assembly in  right side axle
support half.
8.
While applying a light load to either side gear, rotate
either pinion gear until the side  gears have made one
complete revolution.
13.Coat a new  O-ring with grease and install left side
axlesupporthalf.Tightenaxlesupportcasescrewsfrom
35
to 41 ft-lb (47 to 56 N--m).
9.
Ideal tooth contact should cover more than 35% of
each tooth surface. The contact area should  be in the
center of each tooth and extend 1/3 to 1/2 way across
each tooth from the toe (small) end (Fig. 40).
14.Install input  shaft/pinion gear assembly  (see Input
shaft/Pinion in this section of this manual).
15.Coat
new O-rings with grease, align differential shaft
10.Adjust
side gear shims if necessary to correct tooth
splines with differential gear assembly and slide differ-
ential shaft assemblies onto axle support.
contact. Recheck  differential pinion gear to  side gear
backlash if any changes are made.
16.Install
bevel gear case/axle  case assemblies (see
11.
After  backlash and  tooth  contact  have been  ad-
Bevel Gear Case/Axle Case Assembly in this section of
this manual).
justed, align the hole in the differential pinion shaft with
the hole in the differential case and install a new spring
pin.
Axles, Planetaries and Brakes
Page 6 -- 28
Groundsmaster 4100--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 298 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

One thought on “Toro 08162SL Model 30413 Groundsmaster 4100 D Service Manual

  1. At only 700mm wide the Mini Dumper is even at home on tight access
    sites. No need to grunt, groan, and force the
    mower about the yard. The US will be getting a revised 2011 Jeep Wrangler but the diesel option will not be offered in the United States.

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website