Toro 08162SL Model 30413 Groundsmaster 4100 D Service Manual

Input Shaft/Pinion Gear
1
35
(47
to 41 ft--lb
to 56 N--m)
18
2
3
17
4
5
6
7
16
8
18
9
15
10
14
10
9
13
35
(47
to 41 ft--lb
to 56 N--m)
11
12
Figure 30
1.
2.
3.
4.
5.
6.
Nut (2 used)
Lockwasher (2 used)
Stud (2 used)
Locknut
Stake washer
Oil seal
7.
8.
9.
O-ring
13. Shim
Seal collar
Bearing
14. Screw (2 used)
15. Gear case
16. Gasket
10. O-ring
11. Input shaft/pinion gear
12. Bearing case
17. Cover plate
18. Dowel pin
The following procedures assume the rear axle assem-
bly has been removed from the machine (see Rear Axle
Assembly Removal in this section).
Installation (Fig. 30)
NOTE:  When installing new bearing cones, press only
on the inner race of the bearing cone.
Removal (Fig. 30)
1.
If the inner bearing cone was removed, press a new
1.
sembly from the axle assembly.Remove thegasketand
any remaining gasket material.
Remove the cover plate, gasket and gear case as-
bearingconeallthewayontotheinputshaft/piniongear.
2.
Place the shaft and bearing assembly in the bearing
case and install the outer bearing cone.
2.
the input shaft/pinion gear.
Remove the retaining rings and the driven gear from
NOTE:  The  bearings  must   be  completely   seated.
There should be no input shaft/pinion gear end play.
3.
gear case.  Remove  the shims  and bearing  case O-
rings.
Remove input shaft/pinion gear assembly from  the
3.
(Fig. 31). The  seal should be installed with  the garter
spring towards the hydraulic motor.
Coat a new oil seal with grease and install as shown
4.
Remove and discard the stake washer.
Release the stake washer and remove the locknut.
4.
seal collar and install the collar.
Coat new O-ring with grease. Install O-ring in the oil
5.
bearing cone and bearing  case. Remove and discard
the oil seal and O-ring.
Drive the input shaft/pinion gear out from the outer
5.
tight.
Install a new stake washer. Install the lock nut finger
6.
Setthebearingpreloadbysecuringthebearingcase
6.
cases for damage and  wear. Replace components as
necessary.
Inspect  all  gears,  shafts, bearings,  spacers  and
in a vise. Thread a M12 x 1.5 hex head cap screw into
the splined end of the input shaft/pinion gear and slowly
tighten the locknut until 4 to 6 in-lb (0.4 to 0.7 N--m) of
force is required to rotate the input shaft/pinion gear in
the bearing case.
NOTE:  Replacement input shaft/pinion gears are only
available in matched ring and pinion sets.
Axles, Planetaries and Brakes
Page 6 -- 24
Groundsmaster 4100--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 298 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

One thought on “Toro 08162SL Model 30413 Groundsmaster 4100 D Service Manual

  1. At only 700mm wide the Mini Dumper is even at home on tight access
    sites. No need to grunt, groan, and force the
    mower about the yard. The US will be getting a revised 2011 Jeep Wrangler but the diesel option will not be offered in the United States.

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website