Removal (Fig. 6)
Position machine on a clean, level surface. Lower
3
1.
cutting deck and engage parking brake.
2.
Fully raise wing deck, stop engine and remove key
from the ignition switch. Remove three (3) washer head
screws and shield strap that secure flex shield to wing
deck. Lower wing deck.
2
3.
ting Deck Motor Removal in the Service and Repairs
Section of Chapter 4 -- Hydraulic System).
Remove hydraulic motor from wing deck (see Cut-
1
2
4.
der clevis to the wing deck (Fig. 7).
Remove cap screw and lock nut that secure lift cylin-
Figure 7
3.
1.
2.
Hydraulic motor
Flange head screw
Lift cylinder clevis
5.
6.
Remove switch shield (item 50) from center deck.
Support wing deck to prevent it from falling as links
Front of center deck
are removed.
7.
end of both links. Cap screw on rear link also uses a flat
washer (item 28).
Remove cap screw (item 29) from pivot pin on upper
NOTE: When removing pivotpins fromdeck,noteloca-
tion of thrust washers (item 6) and hardened spacers
(item 42).
0.060”
to 0.090”
(1.5
(wing lowered & latched)
to 2.2 mm)
8.
26)
Remove flange nut (item 19) from carriage bolt (item
and pull pivot pins (item 18) from deck. Locate and
retrieve thrust washers (item 6) and hardened spacers
(item 42) from between links and deck brackets.
9.
Slide the wing deck away from the center deck.
required, remove link(s) from wing deck by remov-
Wing opens this way
10.If
Figure 8
ing lock nut and flat washer that secure tapered stud to
deck. Press tapered stud from deck to remove link as-
sembly. Remove foam washer (item 42) and link skid.
Installation (Fig. 6)
1.
engage parking brake and remove key from the ignition
switch.
Park machine on aclean, levelsurface. Stopengine,
0.380” to 0.620”
(9.7
to 15.7 mm)
2.
If links were removed from wing deck, thoroughly
1
clean tapered stud on link and mounting boss of wing
deck. Place foam washer on tapered stud and insert
stud into deck mounting boss. Position link skid to stud
andsecurewithflatwasherandlocknut.Torquelocknut
from 160 to 180 ft--lb (217 to 244 N--m).
2
Figure 9
1.
Wing deck blade
2.
Center deck blade
NOTE: Pivot latches (item 8) may need to be manually
opened prior to wing deck installation. If necessary, use
a pry bar to carefully open latch.
3.
Position the wing deck to the center deck.
Groundsmaster 4100--D
Page 8 -- 11
Cutting Deck
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 30413, Toro Groundsmaster Groundsmaster 4100 D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)
At only 700mm wide the Mini Dumper is even at home on tight access
sites. No need to grunt, groan, and force the
mower about the yard. The US will be getting a revised 2011 Jeep Wrangler but the diesel option will not be offered in the United States.