NOTE: The front frame needs to be lowered from the
main frame to allow clearance to remove the hydraulic
reservoir from the machine.
Inspection
1.
Clean hydraulic reservoir and suction strainer with
solvent.
Removal (Fig. 47)
2.
Inspect for leaks, cracks or other damage.
1.
stop engine, engage parking brake and remove key
from the ignition switch.
Park machine on a level surface, lower cutting deck,
Installation (Fig. 47)
1.
Using a wrench, turn tank strainer into port at least
to 2 full turns beyond finger tight.
1--1/2
2.
Remove front cutting deck (see Cutting Deck Re-
moval in the Service and Repairs section of Chapter 8
2.
Position reservoir to machine.
--
Cutting Deck).
3.
Align frame mounting holes and support front frame to
prevent it from moving.
Carefully raise front frame assembly to main frame.
3.
Installing Hydraulic System Components at the begin-
ning of the Service and Repairs section of this chapter.
Read the General Precautions for Removing and
4.
(item 31), flat washers (item 28) and flange nuts (item
30).
Secure front frame to main frame with cap screws
4.
5.
Drain reservoir into a suitable container.
Disconnect hydraulic hoses from reservoir. Label
disconnected hydraulic lines for proper installation.
5.
6.
Lower machine to ground.
6.
Remove straps (items 4 and 8) that secure reservoir
to front frame. Remove felt straps (item 3) from between
straps and reservoir.
Position felt straps (item 3) between straps and res-
ervoir. Secure reservoir to front frame with straps (items
4
and 8).
7.
To allow front frame to be lowered for reservoir re-
7.
Remove caps and plugs from hydraulic lines and fit-
moval, remove hydraulic tubes that connect hydraulic
components on front frame (wheel motors and front
deck PTO manifold) to components on main frame. Put
caps or plugs on open hydraulic lines and fittings.
tings that were placed during the removal process. Us-
ing labels placed during removal, connect hydraulic
hoses and tubes to fittings on reservoir, wheel motors
and hydraulic manifold (see Hydraulic Hose and Tube
Installation in the General Information section of this
chapter).
8.
ing. Use jack or hoist to raise front of machine and sup-
port machine with jackstands.
Chockrearwheelstopreventthemachinefrommov-
8.
Install front cutting deck (see Cutting Deck Installa-
tion in the Service and Repairs section of Chapter 8 --
Cutting Deck).
9.
Support front frame to prevent it from moving.
10.Remove
and flange nuts (item 30) thatsecure front frame tomain
frame.
capscrews (item 31), flatwashers (item 28)
9.
Fill reservoir with new hydraulic fluid to proper level.
fill hydraulic system (see Charge Hydraulic
10.Properly
System in this section).
11.
Carefully lower front frame assembly to allow clear-
ance for reservoir removal. Once lowered, support front
frame to prevent it from shifting.
11.
hydraulic reservoir oil level.
Stop engine and check for hydraulic oil leaks. Check
12.Carefully
remove hydraulic reservoir from machine.
Groundsmaster 4100--D
Page 4 -- 65
Hydraulic System
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 30413, Toro Groundsmaster Groundsmaster 4100 D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)
At only 700mm wide the Mini Dumper is even at home on tight access
sites. No need to grunt, groan, and force the
mower about the yard. The US will be getting a revised 2011 Jeep Wrangler but the diesel option will not be offered in the United States.