Toro 08162SL Model 30413 Groundsmaster 4100 D Service Manual

Procedure  for  Lift/Lower  Circuit Relief  Pressure
Test
3
NOTE:  Before attempting to check or  adjust lift pres-
sure, make sure  that counterbalance pressure is  cor-
rectly adjusted.
2
1.
perature by operating the machine for approximately 10
minutes. Make sure the hydraulic tank is full.
Make sure hydraulic oil is at normal operating tem-
2.
lowered and off. Make sure engine is off and the parking
brake is engaged.
Parkmachineonalevelsurfacewiththecuttingdeck
4
1
Figure 41
CAUTION
1.
2.
Fan drive manifold
Lift circuit test port
3.
4.
Lift control valve
Relief valve
Prevent personal injury and/or damage to equip-
ment. Read all WARNINGS, CAUTIONS and Pre-
cautions for Hydraulic Testing at the  beginning
of this section.
2
3
3.
Raise seat  to gain access  to hydraulic test  fitting.
Connect a 5,000 PSI (345 bar) gauge to lift circuit test
port(Fig.41).Routegaugehosetoallowseattobesafe-
ly lowered.
4
5
4.
at idle speed. Check for hydraulic leakage and correct
before proceeding with test.
After installing pressure gauge, start engine and run
1
5.
(2870
Sit on the seat and operate the engine at full speed
RPM).
6.
While sitting on the seat, pull lift lever back to raise
the cutting deck. Momentarily hold the lever with the lift
cylinder fully retracted (deck fully raised) while looking
at the gauge.
Figure 42
1.
2.
3.
Control valve assembly
Relief valve assembly
Washers
4.
5.
Spring
Poppet
GAUGE READING TOBE2500to2550PSI   (173to
175
bar).
7.
8.
valve by rotating counterclockwise (Figure 42). If pres-
sure is too low, check for restriction in pump intake line.
Check the lift cylinder for internal leakage. If cylinder is
not leaking, adjust the relief valve by rotating clockwise.
If pressure is still too low, pump or lift cylinder(s) should
be suspected of wear, damage or inefficiency.
Stop the engine and record test results.
If pressure is too high, adjust relief valve in lift control
9.
When  testing  is completed,  disconnect  pressure
gauge from test port.
Groundsmaster 4100--D
Page 4 -- 53
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 298 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

One thought on “Toro 08162SL Model 30413 Groundsmaster 4100 D Service Manual

  1. At only 700mm wide the Mini Dumper is even at home on tight access
    sites. No need to grunt, groan, and force the
    mower about the yard. The US will be getting a revised 2011 Jeep Wrangler but the diesel option will not be offered in the United States.

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website