Roller
Removal
5
9
6
7
1.
Park mower on a level surface. Make sure engine
is OFF. Remove high tension lead from the spark plug.
2
2.
Loosen jam nut and set screw on both ends of the
mower.
1
3.
On one end of the mower, remove lock nut and flat
washer from the carriage screw.
10
Note:
Do not adjust the height–of–cut screw when re-
3
moving the height–of cut arm.
8
4.
Pull the height–of–cut arm from the roller shaft, car-
4
riage screw, and height–of–cut bracket. Remove the
roller from the mower.
Figure 34
1.
2.
3.
4.
5.
Jam nut
6.
7.
8.
9.
Height–of–cut screw
Height–of–cut arm
Roller
Set screw
Lock nut
Flat washer
Installation
Height–of–cut bracket
1.
Place roller shaft into the height–of–cut arm that is
Carriage screw
10. Frame
still attached to the mower.
3.
arms. Tight roller shafts in place by tightening the set
screw and then the jam nut.
Center roller evenly between both height–of–cut
2.
Placetheremovedheight–of–cutarmontotheroller
shaft. Secure height–of–cut arm into the height–of–cut
bracket with with the carriage screw, flat washer, and
lock nut.
4. Adjustrollerforheight–of–cut(seeHeight–of–Cutin
the Adjustments section).
Roller Bearing Replacement
Note:
tions is the same for full, swaged, and wiehle rollers.
A Wiehle roller is shown. Bearing configura-
2
1
3
Remove Bearings
Note:
Use the bearing replacement tool kit, described
in the Special Tools section, to remove the roller bear-
ings.
Note:
It is recommended to replace bearings at both
ends of the roller after bearing failure.
1.
to drill a hole in the bearing shaft.
If a hole is not on the bearing shaft, use drill bushing
BEARING AND ROLLER
SURFACE MUST BE FLUSH
Figure 35
2.
3.
Remove roller bearing with bearing puller.
1.
2.
Roller bearing
Roller (Wiehle)
3. Grease fitting
Clean roller bearing cavity and remove any rust with
crocus cloth.
2.
Press roller bearing into roller so that the outside
surface of the bearing is flush with the end of the roller.
4.
Repeat above steps for the other roller bearing.
3.
based grease until grease appears at the seal of the
bearing.
Grease the bearing with No. 2 multipurpose lithium
Install New Bearings
1.
Make sure roller bearing cavity is clean and free of
dirt. Apply No. 2 multipurpose lithium based grease to
the roller bearing.
4.
Repeat above steps for the other roller bearing.
Greensmaster 1000/1600
Page 7 – 17
Cutting Unit
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Greensmaster 1000, Toro Greensmaster 1600, Toro Greensmaster 96889SL |
| Download File |
|
| Document Type | Catalog |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)