Cutting Reel
Removal
4
8
1.
Park mower on a level surface. Make sure engine
3
is OFF. Remove high tension lead from the spark plug.
2.
stable work bench.
Make sure mower is on a flat level surface or on a
6
7
3.
instructions in Frame Assemblies (RH and LH).
Remove grooming reel kit following the Removal
2
1
4.
Remove bedbar from the mower (see Bedbar Re-
movalinServiceandRepairssectionofChapter7–Cut-
ting Unit).
RIGHT
5
FRONT
5.
Removegreasefittingsfrombothbearinghousings.
Mark bearing housing (RH) for reassembly purposes
(Fig. 32 and 33).
Figure 32
6.
wood, and remove lock nut from the cutting reel shaft
(Fig. 33).
Secure cutting reel from turning with a block of hard
1.
2.
3.
4.
Grease fitting
Bearing housing (RH)
Frame
5.
Small seal
Retaining ring
Bearing
6.
7.
8.
Large seal
Wave washer
7.
(Fig. 32 and 33). Remove the reel from the mower.
Pull both bearing housings from the frame and reel
5
7
1
8.
tenance purposes, remove bearings from both bearing
If bearings are worn or need replacement for main-
2
4
housings as follows:
A. Remove bearing seal, retaining ring, bearing,
and wave washer from the bearing housing (RH).
Discard wave washer (Fig. 32).
LEFT
B. Remove large seal, small seal, and bearing from
the bearing housing (LH) (Fig. 33).
6
FRONT
3
Installation
Figure 33
1.
Make sure engine is OFF. Remove high tension
lead from the spark plug. Place mower on a flat level sur-
face or on a stable work bench.
1.
2.
3.
4.
Grease fitting
Bearing housing (LH)
Bearing lock nut
Large seal
5.
6.
7.
Small seal
Bearing
Frame
IMPORTANT: Make sure correct bearing housing is
used when installing bearings. The grease fitting
hole should face forward when the housing is
placed in the frame.
B. Place small seal into the bearing housing with
the flat side out.
C. Place new wave washer into bearing housing.
Press new bearing into the bearing housing with a
bearing driver.
2.
(Fig. 32).
Reassemble bearing housing (RH) components
IMPORTANT: Make sure the correct bearing hous-
ing is used when installing bearings. The grease fit-
ting hole should face forward when the housing is
placed in the frame.
D. Install and seat retaining ring into the groove of
the housing.
E. Place large seal on the bearing housing with the
flat side out. Press seal in with a seal driver.
A. Bearing housing (RH) should be marked from
disassembly.
Grooming Reel Kit
Page 8 – 20
Greensmaster 1000
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Greensmaster 1000, Toro Greensmaster 1600, Toro Greensmaster 96889SL |
| Download File |
|
| Document Type | Catalog |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)