Installation
B. Make sure grease fitting hole is position to the
front of the mower.
1.
Make sure engine is OFF. Remove high tension
lead from the spark plug. Place mower on a flat level sur-
face or on a stable work bench.
C. Attach the groomer arm cover to the bearing
housing and frame with the two flat head screws,
cover standoffs, and lock nuts. Do not tighten down
fasteners.
IMPORTANT: Make sure the correct bearing hous-
ing is used when installing bearings. The grease fit-
ting hole should face forward when the housing is
placed in the frame.
6. Attach bearing housing (LH) through the frame onto
the reel shaft (Fig. 37).
2.
(Fig. 37).
Reassemble bearing housing (LH) components
A. Push housing onto reel shaft. If necessary, tap
into position with a soft hammer.
A. Place small seal into the bearing housing with
the flat side out.
B. Make sure grease fitting hole is position to the
front of the mower.
B. Press new bearing into the bearing housing with
a bearing driver.
C. Align housing holes to frame holes with both cap
screws and lock nuts. Fasteners should be only fin-
ger tight.
C. Place large seal on the bearing housing with the
flat side out. Press seal in with a seal driver.
7. While tightening the bearing lock nut (Fig. 37) to the
reel shaft, tighten pulley and drive assembly (Fig. 36) to
thereelshaftatthesametime.Torqueassemblyandnut
to 50 ft–lb (6.9 kg–m).
3.
Reassemble bearing housing (RH) components
(Fig. 36).
A. Bearing housing (RH) should be marked from
disassembly.
8.
bearing housing (RH) to the frame (Fig. 36).
Tighten flat head screws and nuts securing the
B. Place small seal into the bearing housing with
the flat side out.
9.
Remove both cap screws and lock nuts holding the
bearing housing (LH) to the frame. Position bearing cov-
er to housing and secure to frame with both cap screws
and lock nuts (Fig. 37).
C. Place new wave washer into housing. Press
new bearing into the bearing housing with a bearing
driver.
10.
Reinstall reel drive belt to the pulley and drive as-
sembly (see Service and Repair section of Chapter 4
Traction and Reel Drive Systems).
D. Install and seat retaining ring into the groove of
the housing.
11.
cap screws to the mower. Tighten cap screws (Fig. 36).
Reinstall reel drive cover with four lock washers and
E. Place large seal on the bearing housing with the
flat side out. Press seal in with a seal driver.
12.
Lubricate both housings with No. 2 multipurpose lithium
base grease (Fig. 37 and 36).
Reinstall grease fittings to both bearing housings.
4.
The reel shaft end with internal threads should be on the
right side of the frame.
Position reel in frame to accept bearing housings.
13.
al).
Reinstall bedbar to the mower (see Bedbar Remov-
Note:
ance but can not be interchanged. The bearing housing
(RH) was marked during disassembly.
The two bearing housings are similar in appear-
14.
Complete mower set–up and adjustment sequence
(see Adjustments section).
5.
Attachbearinghousing(RH)throughtheframeonto
the reel shaft (Fig. 36).
A. Push housing onto reel shaft. If necessary, tap
into position with a soft hammer.
Greensmaster 1000/1600
Page 7 – 19
Cutting Unit
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Greensmaster 1000, Toro Greensmaster 1600, Toro Greensmaster 96889SL |
| Download File |
|
| Document Type | Catalog |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)