Reel
Removal
2
5
1.
Make sure engine is OFF. Remove high tension
lead from the spark plug. Place mower on a flat level sur-
face or on a stable work bench.
3
6
10
2.
Remove bedbar from the mower (see Bedbar Re-
17
13
moval).
4
18
7
12
3.
If a grooming reel kit is installed, remove the cutting
8
reel using the procedures in Frame Assembles (RH and
LH) and Cutting Reel in the Service and Repairs section
of Chapter 8 – Grooming Reel Kit.
14
16
RIGHT
11
4.
reel drive cover from the mower. Mark bearing housing
(RH) for reassembly purposes (Fig. 36).
Remove four cap screws, four lock washers, and
1
FRONT
9
15
Figure 36
5.
sembly (see Service and Repair section of Chapter 4 –
Traction and Reel Drive Systems.
Remove reel drive belt from the pulley and drive as-
1.
2.
3.
4.
5.
6.
7.
8.
9.
Grease fitting
Cap screw
10. Groomer arm cover
11. Cover standoff
Lock washer
Reel drive cover
Reel drive belt
Pulley and drive assy
Retaining ring
Flat head screw
Nut
12. Bearing housing (RH)
13. Frame
IMPORTANT: Do not disassemble the pulley and
drive assembly and retaining ring.
14. Large seal
15. Small seal
16. Retaining ring
17. Bearing
6.
Use a 1/2–inch drive in the pulley and drive assem-
18. Wave washer
bly (Fig. 36) to remove the assembly from the reel drive
shaft. Also, remove bearing lock nut (Fig. 37) from the
reel drive shaft at the same time.
8
10
4
1
2
7.
Use an allen wrench and remove both flat head
screws, groomer arm cover, and both cover standoffs
from the bearing housing (Fig. 36).
7
5
8.
Remove both cap screws, lock nuts, and bearing
cover from the bearing housing (LH) (Fig. 37).
9.
(Fig. 36 and 37).
Remove grease fittings from both bearing housings
RIGHT
9
FRONT
6
10.
Pull both bearing housings from the frame and reel
3
(Fig. 36 and 37). Remove the reel from the mower.
Figure 37
11.
tenance purposes, remove bearings from both bearing
housings as follows:
If bearings are worn or need replacement for main-
1.
2.
3.
4.
5.
Grease fitting
Bearing housing (LH)
6.
Bearing lock nut
Large seal
Small seal
Bearing
7.
8.
9.
Cap screw
Lock nut
Bearing cover
A. Remove large seal, small seal, and bearing from
the bearing housing (Fig. 37).
10. Frame
B. Remove bearing seal, retaining ring, bearing,
andwavewasherfromthebearinghousing.Discard
wave washer (Fig. 36).
Cutting Unit
Page 7 – 18
Greensmaster 1000/1600
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Greensmaster 1000, Toro Greensmaster 1600, Toro Greensmaster 96889SL |
| Download File |
|
| Document Type | Catalog |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)