Toro 01088SL Rev F Service Manual Groundsmaster 3500 D Preface Publication

11.
Traction Belt).
Install traction belt to the pump pulley (see Replace
CAUTION
12.Using
a straight edge across  the lower face of the
Support piston and gear pumps when installing
them to the machine to prevent them from falling
and causing personal injury.
pumppulley,verifytractionbeltalignmentacrossengine
and pump pulleys. Slide pulley and taper lock bushing
on pump shaft so that traction belt and straight edge are
aligned indicating correct position of  pump pulley. Se-
cure taper lock bushing in position with set screw.
8.
Positionpumpmountplatewithpumps,pumppulley,
and idler assembly to the machine. Install fasteners and
spacers securing the pump mount  plate to the engine
and pump support. Tighten fasteners securely.
IMPORTANT: Whentightening bushing capscrews,
tighten in three equal steps and inacircular pattern.
13.Secure
taperlockbushingbytighteningthree(3)cap
9.
draulic hoses as follows:
Remove plugs from hydraulic hoses. Connect all hy-
screws to a  torque from 90 to 120  in--lb (10.2 to 13.6
N--m) in three equal steps and in a circular pattern to se-
cure pulley and taper lock bushing.
A.  Secure o--rings, fittings, and hydraulic hoses  to
the gear pump.
14.Check
that belt alignment is still correct. If needed,
B.  Connect hydraulic suction hose from the hydrau-
lictanktothegearpumpbarbfittingwithhoseclamp.
loosenandre--adjustpulleyandtaperlockbushingloca-
tion on pump shaft to allow for correct belt alignment.
C. Secure  o--rings, fittings, and hydraulic hoses to
the piston pump.
15.Fill hydraulic tank with new hydraulic fluid (see Trac-
tion Unit Operator’s Manual).
10.Install
follows:
neutral arm assembly to the piston pump as
16.Adjust traction drive for neutral (see Adjust Traction
Drive for Neutral).
A.  Position neutral bracket to the mount  plate and
the pump lever to the pump trunnion.
B.  Secure pump lever to the piston pump trunnion
with flat washer and cap screw.
C. Secure neutral bracket to the pump mount plate
with flange head screw and flange nut. Secure neu-
tral bracket to the piston pump with both flange head
screws.
D. Connect traction control cable to the pump lever.
CAUTION
The extension spring is under tension and may
cause  personal injury  during installation.  Use
caution when installing the  spring to the pump
lever.
E.  Install  extension  spring  to  the  cable  support
bracket and neutral arm.
Groundsmaster 3500--D
Page 4 -- 97
Hydraulic System (Rev. D)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 256 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website