Toro 01088SL Rev F Service Manual Groundsmaster 3500 D Preface Publication

Note:
not have a flat washer with it.
The cap screw next to the torsion spring does
1
2
2
B.  Remove five cap screws, four washers, and five
spacers securing the pump  mount plate to the en-
gine.
4
C. Remove four cap screws and hardened washers
securing the right engine mounting bracket and hy-
drostat to the engine.
3
2
16.As
necessary, remove engine mounts, front engine
1
mounting bracket, throttle support bracket and left en-
gine mounting bracket.
Installation
Figure 32
1.
If  removed,  install  engine  mounts,  front   engine
1.
2.
Cap screw
Spacer
3.
4.
Torsion spring
Pump mount plate
mounting bracket, throttle support bracket and left en-
ginemountingbracket.Also,makesurethatallswitches
and sensors are installed on engine.
2.
Install hydrostat and pump mount plate to the engine
as follows (Figs. 32 and 33):
A.  Secure right engine  mounting bracket  and hy-
drostat to  the engine with  four hardened washers
and cap screws.
1
Note:
Do not install flat washer with  cap screw near
the torsion spring to prevent the spring from binding.
3
6
1
B.  Secure pump mount plate to the engine with five
spacers, four washers, and five cap screws.
C. Install traction belt to the engine flywheel and hy-
drostat pulleys (see Traction Belt Replacement).
4
5
2
3
3.
Connect hoist or lift to the front and  rear engine lift
tabs (Fig. 29 and 30).
Figure 33
1.
2.
3.
Long spacer (4 used)
Flat washer (3 used)
4.
5.
Hardened washer
10 mm cap screw
Short spacer
8 mm cap screw (4 used)
6.
CAUTION
7.
Install all  hydraulic  hoses to  the piston  and  gear
pumps. Install traction control cable to the neutral arm
assemblyonthepistonpump(seePistonPumpInstalla-
tion in Chapter 4-- Hydraulic System).
One person should operate lift or hoist while the
otherpersonguidestheengineintothemachine.
IMPORTANT: Make sure not to damage the engine,
fuel and hydraulic lines, electrical harness, or other
parts while installing the engine.
8.
28)
Connect fuel hose to the fuel/water  separator (Fig.
and front injector nozzle.
9.
siontankandbrackettothetopfanshroud(seeRadiator
Installation).
Install top fan shroud to the  radiator. Install expan-
4.
5.
Position engine slowly into the machine.
Secure all three engine mounts to the engine mount-
ing brackets with cap screws, washers, and flange nuts.
6.
Secure wire harness to the front lift tab and the en-
gine with cable ties.
Kubota Diesel Engine
Groundsmaster 3500--D
Page 3 -- 26    Rev. D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 256 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website