Toro 01088SL Rev F Service Manual Groundsmaster 3500 D Preface Publication

Rear Roller Service (Non--Greasable Bearings)
Seal Removal (Fig. 16)
5.  Install second spiral retaining ring onto roller shaft to
secure second bearing.
1.
Using a 1/4 inch thick, 3” X 3” square piece of steel,
make a seal removal tool as shown in Figure 17.
6.  Install new seals to .030 inch (.76 mm) recessed into
roller.
2.
3.
Slide seal removal tool over roller shaft.
Using the tool as a template, locate, mark, and drill
two 7/64 inch (.109 inch diameter) holes in outer face of
seal.
2
3
4
5
4.
ScrewtwoNo.8(.164inchdiameter)by3/4inchlong
self--tapping screws into outer face of seal.
5.
removal tool.
Install two1/4--20by 1 inch long cap screws into seal
1
6.
assembly.
Alternatelytightencapscrewstopullsealoutofroller
Figure 16
1.
2.
3.
Roller
Roller shaft
Bearing
4.
5.
Retaining ring
Oil seal
NOTE:  Seals will be destroyed when servicing the rear
roller. Do not re--use seals that have been removed.
.188”
dia. (2)
.625”
Bearing Removal (Fig. 16)
dia.
NOTE:  The bearings are pressed onto the roller shaft
and loose fit into the roller.
.625”
.625”
1.
from roller shaft: catch ring removal notch with pick and
pull ring from shaft.
Remove seals  from roller. Remove retaining  rings
Tap 1/4--20
UNC (2)
2.
Loosely secure  roller assembly in  bench vise and
lightly tap one end of roller shaft until free from bearing
and housing.
1.05”
1.05”
3.
bearing on inner race and tapping on roller shaft.
Remove second  bearing from shaft  by supporting
Figure 17
4.
rings, and roller for  damage. Replace components as
needed.
Discard removed bearings. Inspect shaft,  retaining
Roller Assembly (Fig. 16)
1.
pressure equally to inner and outer bearing races.
Press newbearingontooneendofrollershaft.Apply
2.
Place spiral retaining ring on same end  of shaft as
installed bearing.
3.
4.
pressure equally to inner and outer bearing races. The
inner race  will contact shoulder  of shaft  before outer
race contacts shoulder of roller.
Install shaft with single bearing into roller.
Install second new bearing  onto roller shaft. Apply
Cutting Units (Rev. D)
Page 7 -- 12   Rev. E
Groundsmaster 3500--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 256 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website