Toro 01088SL Rev F Service Manual Groundsmaster 3500 D Preface Publication

Cutting Blade Removal and Installation
Thecutting blademust bereplaced  ifasolid object ishit,
thebladeis  outofbalance,or  ifthe bladeis bent.Always
use genuine TORO replacement  blades to be sure of
safety and optimum performance.  Never use replace-
ment blades  made  by other  manufacturers  because
they could be dangerous.
4
1
1.
Park machine on a level surface, raise cutting units
2
3
to highest position, stop engine, engage parking brake,
and remove key from the ignition switch. Block cutting
deck to prevent it from falling accidentally.
2.
padded glove. Remove blade bolt, anti--scalp cup, and
blade from spindle shaft.
Grasp end  of cutting  blade using  a rag  or thickly
85
(115
to 110 ft--lb
to 149 N--m)
3.
scalp cup, and blade bolt. Tighten bolt from 85 to 110 ft--
lb (115 to 149 N--m).
Install blade (sail facing toward cutting deck), anti--
Figure 10
3.
4.
1.
2.
Cutting blade
Anti--scalp cup
Blade bolt
Spindle shaft
Inspecting and Sharpening Blade
1.
Park machine on a level surface, raise cutting units
higher than the heel, the blade is bent or warped, and
must be replaced.
to highest position, stop engine, engage parking brake,
and remove key from the ignition switch. Block cutting
deck to prevent it from falling accidentally.
WARNING
Do not  try to straighten a  blade that is  bent.
Never weld a broken or cracked blade. Always
use a  new blade  to assure continued  safety
certification of the product.
2.
Examine cutting ends of  the blade carefully, espe-
cially where the flat and curved (sail) parts of the blade
meet (Fig. 11). Since  sand and abrasive material  can
wear away the metal that connects the flat part and sail
of the blade, check the blade before using the machine.
If wear is noticed, replace the blade.
Figure 11
3.
Inspect cutting edges of all blades. Sharpen the cut-
ting edges if they are dulled or nicked. Sharpen only the
top of the cutting edge and maintain the original cutting
angletomakesureofsharpness(Fig.12).Thebladewill
remain balanced  if the  same amount  of metal  is re-
moved from both cutting edges.
SHARPEN AT THIS
ANGLE ONLY
4.
To check  blade for being  straight and parallel,  re-
moveblade(seeCutterBladeRemovalandInstallation)
and lay it on a level surface. The ends of the blade must
be slightly lower than  the center and the cutting edge
must be lower than the heel of the blade. If the blade is
higher at the ends than the center, or if cutting edge is
BLADE END VIEW
Figure 12
Cutting Units (Rev. D)
Page 7 -- 10
Groundsmaster 3500--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 256 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website