Toro 01088SL Rev F Service Manual Groundsmaster 3500 D Preface Publication

Rear Roller
Three  types of  rear  rollers  have been  used  on  the
Groundsmaster 3500--D. One roller design has sealed
bearings with no grease fittings on the roller shaft. The
second design  has  grease fittings  in the  roller  shaft
ends. The third design has grease fittings incorporated
into the roller fasteners. Removal and installation of the
rear roller from the cutting deck is the same, regardless
of roller type.
2
9
3
8
1
4
5
3
6
4
2
Removal (Fig. 13)
1.
stop engine,  engage parking  brake, and remove  key
from the ignition switch.
Park machine on a level surface, lower cutting units,
5
6
7
Figure 13
2.
If cutting  deck is  equipped with roller  scraper, re-
move roller scraper from deck.
1.
2.
3.
4.
5.
Cutting deck frame
Flange head screw
Cap screw
6.
7.
8.
9.
Cap screw
Rear roller
Cap screw (if equipped)
Grease fitting
A.  If equipped with  early style  roller scraper (Fig.
Roller mount
14),
loosen one locknut that secures  roller scraper
Skid bracket
rod to mounting bracket.
EARLY STYLE
2
B.  Remove fasteners securing left and right scraper
rod brackets to roller mounts (Figs. 14 and 15).
C. Removescraper  rodassembly fromcuttingdeck.
3.
mountstorearofdeckframe.Removerollermountsand
rear roller assembly from deck frame.
Remove four  (4) mounting  screws securing  roller
1
4
3
4.
Loosen fasteners securing eachend ofroller toroller
mounts. Remove mounts from roller.
Figure 14
1.
2.
Roller mount
Scraper rod (early style)
3.
4.
Set screw
Locknut
Installation (Fig. 13)
1.
2.
deck frame. Secure assembly to deck frame with flange
head screws.
Place roller assembly into roller mounts.
LATER STYLE
Install roller and roller mount assembly  into rear of
3
2
1
4
IMPORTANT: If roller design includes grease fittings in
roller fasteners (items 8 and 9 in Fig. 13), make sure the
grease  groove in  each  roller  mount  aligns with  the
grease hole in each end of the roller shaft. To help align
the groove and hole, there is also an alignment mark on
one end of the roller shaft.
5
3.
Tighten fasteners that secure  each end of roller to
Figure 15
roller mounts.
1.
2.
3.
Roller scraper
Scraper plate
Cap screw
4.
5.
Cap screw
Jam nut
4.
mounts. Adjust scraper rod (see Adjust Roller Scraper
in the Adjustments section).
If equipped,  install scraper  rod assembly  to roller
5.
If  roller  design   allows  greasing,  lubricate  roller
grease points.
Groundsmaster 3500--D
Page 7 -- 11  Rev. E
Cutting Units (Rev. D)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 256 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website