Toro 03126SL Rev C Service Manual Serial No 240000001 Above Workman 3000 4000

Testing
The most effective method for isolating problems in the
hydraulic system is  by using hydraulic  test equipment
such as pressure gauges and flow meters in the circuits
during various operational  checks. (See Special Tools
section in this Chapter.)
3.  The engine must be in good operating condition. Use
a  tachometer when  making  a  hydraulic test.  Engine
speed will affect the accuracy of the tester readings.
4.
Because the hydraulic pump is belt driven, check for
proper pump belt adjustment before performing any hy-
draulic test.
CAUTION
5.
To prevent damage to tester or components, the inlet
and the outlet hoses must  be properly connected, and
not reversed (when using tester with pressure and flow
capabilities).
Failure to use gauges with recommended pres-
sure  (psi) rating  as  listed  in test  procedures
could result in  damage to gauge and  possible
personal injury from leaking hot oil.
6.  To minimize the possibility of damaging components,
completely open load valve in hydraulic tester (when us-
ing tester with pressure and flow capabilities).
Before Performing Hydraulic Tests
7.
they are  not cross–threaded, before  tightening the fit-
tings with a wrench.
Install fittings finger  tight, far enough to  insure that
All obvious areas such as oil supply, filter, binding link-
age, loose fasteners, or improper adjustments must be
checked before assuming that a hydraulic component is
the source of the problem being experienced.
8.
Position  the tester  hoses  so  that rotating  vehicle
parts will not make contact with them and result in hose
or tester damage.
Precautions For Hydraulic Testing
9.
connecting hydraulic test equipment.
Check and adjust the oil  level in the transaxle after
WARNING
10.All
oil at normal operating temperature.
hydraulic tests should be made with the hydraulic
Before disconnecting  or performing  any work
on  the  hydraulic  system, all  pressure  in  the
system must be relieved by stopping the engine,
rotating the  steering wheel in  both directions,
lowering or  supporting the  bed and operating
other hydraulic accessories.
11.
After testing is  completed, check and adjust the  oil
level in the transaxle before returning the vehicle to ser-
vice.
Keep body and hands away from pin hole leaks
or nozzles that eject hydraulic fluid under  high
pressure. Use paper or cardboard, not hands, to
search for leaks. Hydraulic fluid escaping under
pressure can have sufficient force to penetrate
skin and cause serious injury. If fluid is injected
into  the  skin,  it must  be  surgically  removed
within a few hours by a doctor familiar with this
type of injury.  Gangrene may result from  such
an injury.
1.
Thoroughly clean the vehicle before disconnecting or
disassembling any hydraulic components. Always keep
in mind the  need for cleanliness when  working on hy-
draulic equipment. Contamination will cause excessive
wear of hydraulic components.
2.
Put caps or plugs on any hydraulic lines left open or
exposed during testing or removal of components.
Workman 3000/4000 Series
Page 9 – 15
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 302 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website