Toro 03126SL Rev C Service Manual Serial No 240000001 Above Workman 3000 4000

Gear Pump (Vehicles with Air Cooled Engine)
Removal (Fig. 22)
3.  Check oil level in transaxle (see Operator’s Manual).
Add Dexron III ATF if necessary.
1.
Park vehicle on a level surface, raise and support bed
(if installed),  shut engine  off and  engage the  parking
brake.
4.  Start the engine and operate at idle speed until air is
out of hydraulic system.
2.
pulley (see Operator’s Manual).
Loosen pump drive belt and remove belt from pump
5.  Stop the engine and check oil level in transaxle (see
Operator’s Manual). Add Dexron III ATF if necessary.
3.
Installing Hydraulic System  Components at the begin-
ning of the Service and Repairs section of this chapter.
Read  the General  Precautions for  Removing  and
9
8
10
11
7
CAUTION
12
6
Before performing any  service or repair  on hy-
draulic   system  components,   relieve   system
pressure  to avoid  injury  from pressurized  hy-
draulic oil. Stop the engine, remove key from the
ignition switch, rotate the steering wheel in both
directions, lower or support the bed and operate
other hydraulic accessories.
1
ANTISIEZE
LUBRICANT
5
4
3
2
130
(14.7
to 160 in–lb
to 18.1 N–m)
4.
caps or  plugs in  hoses to  prevent contamination  and
leakage of hydraulic oil. Install plugs in pump fittings.
Disconnect hydraulic hoses from gear pump. Install
Figure 22
5.
a guide.
Remove gear pump from mount using Figure 22 as
1.
2.
3.
4.
5.
6.
Drive belt
Lock nut
7.
8.
9.
10. Gear pump
11.  Lock nut (2 used)
12. Pressure hose
Mount
Suction hose
Square key
Flat washer
Pump pulley
Cap screw
Installation (Fig. 22)
Carriage screw
1.
Install gear pump to mount using Figure 22 as a guide
and using the following instructions:
A.  Apply antiseize lubricant to gear pump shaft be-
fore installing pulley.
B.  After installing  key  and  pulley on  pump  shaft,
tighten lock nut (Item 8) to a torque from 130 to 160
in–lb (14.7 to 18.1 N–m).
C. Install pump suction hose to fitting on pump, then
fill pump through pressure port of  pump, with clean
Dexron III ATF.
D. Install pump pressure hose to fitting on pump.
2.
After installing  the pump and  connecting hydraulic
hoses, install belt  and adjust belt tension  (see Opera-
tor’s Manual).
Workman 3000/4000 Series
Page 9 – 27
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 302 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website