Toro 03126SL Rev C Service Manual Serial No 240000001 Above Workman 3000 4000

Removal (Fig. 31)
Park vehicle on a level surface, shut engine off and
50
(68
ft--lb
N--m)
1.
engage the parking brake.
2.
Installing Hydraulic System Components at  the begin-
ning of the Service and Repairs section of this chapter.
Read the  General  Precautions for  Removing and
7
8
4
CAUTION
1
Before performing any  service or repair on hy-
draulic  system   components,   relieve  system
pressure to  avoid  injury from  pressurized hy-
draulic oil. Stop the engine, remove key from the
ignition switch, rotate the steering wheel in both
directions, lower or support the bed and operate
other hydraulic accessories.
5
2
3
6
Figure 32
1.
2.
3.
4.
O--ring
5.
6.
7.
8.
90o hydraulic fitting
3.
Label and disconnect hydraulic hoses from steering
45o hydraulic fitting
O--ring
cylinder. Install caps or plugs in hoses to  prevent con-
tamination and leakage of hydraulic oil. Install plugs in
cylinder ports.
O--ring
O--ring
Ball joint
Jam nut
4.
31
Remove steering cylinder fromvehicle using Figures
and 32 as guides.
CYLINDER LENGTH WHEN FULLY RETRACTED
Installation (Fig. 31)
If ball joint was removed from cylinder shaft, fully re-
1.
tractcylindershaftandthreadballjointontoshaft.Adjust
center to center length to dimension shown in Figure 33
before tightening jam  nut. Torque jam nut 50 ft--lb  (68
N--m).
14.520”
15.040”
(36.88 cm) for 2WD
(38.20 cm) for 4WD
2.
Install steering cylinder to vehicle using  Figures 31
and 32 as guides.
Figure 33
3.
move caps and plugs from hoses and fittings. Connect
hydraulic hoses to steering cylinder.
Replace o--rings on hydraulic hoses and fittings. Re-
4.
Check oil level in transaxle (see Operator’s Manual).
Add Dexron III ATF if necessary.
5.
Start the engine, operate at idle speed and rotate the
steeringwheelinbothdirections   untilairisoutofhydrau-
lic system.
6.
Operator’s Manual). Add Dexron III ATF if necessary.
Stop the engine and check oil level in transaxle (see
7.
Check front wheel alignment and adjust as needed
(see Front Wheel Alignment in the Service and Repair
section of Chapter 7 -- Chassis).
Workman 3000/4000 Series
Page 9 -- 39   Rev. A
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 302 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website