Toro 03126SL Rev C Service Manual Serial No 240000001 Above Workman 3000 4000

7.
8.
9.
Carefully slide stub axle from axle housing.
If required, slide driveshaft from transaxle.
If bearings are being serviced, remove axle housing
Assembly (Fig. 8)
1.  If driveshaft was removed from transaxle, apply anti–
seize lubricant to transaxle shaft. Slide driveshaft clamp
end onto splined transaxle shaft.
(15)
from vehicle:
2.
If removed, install axle housing to frame:
A.  Remove brake assembly from axle housing (see
Brake  Service in  Service  and  Repairs Section  of
Chapter 7 – Chassis).
A.  Position axle housing to  frame and install  three
cap screws to secure axle housing to vehicle frame.
NOTE: Upper cap screw for LH axle housing is short-
er than other cap screws used to secure axle housing
to frame.
B.  Remove three (3) cap screws with washers that
secure axle housing to vehicle frame. Remove axle
housing. NOTE: Upper cap screw for LH axle hous-
ing is shorter than other cap screws used to secure
axle housing to frame.
B.  Install brake assembly to axle housing (see Brake
Service in Service and Repairs Section of Chapter 7
Chassis).
Bearing Service (Fig. 8)
3.
If wheel studs  were removed from stub axle,  apply
1.
bearing is removed from stub axle, bearing set must be
replaced.
Inspect bearings  and replace if  necessary. If outer
Loctite #680 (or equivalent) to threads near head of stud.
Install stud with  lock washer into stub axle  and torque
from 40 to 60 ft–lb (54 to 81 N–m).
2.
Remove bearing seal from back of axle housing.
4.
Insert stub axle with greased bearing into axle hous-
ing. Be careful  not to damage the  bearing seal during
installation.
3.
from axle housing noting orientation  of bearing spacer
step (away from stub axle flange).
Remove inner  bearing cone.  Slide bearing  spacer
5.
Slide end yoke onto stub axle shaft.
4.
Press outer bearing cone from stub axle.
Press inner  and outer  bearing cups from  housing.
IMPORTANT:Flange  nut   (1)  should   be  replaced
whenever it is removed.
5.
6.
ing.  Press bearing  cups  into housing  until  they  seat
against the housing shoulder.
Clean all parts thoroughly before reassembly.
6.
axle. Install new flange nut onto screw. Torque flange nut
from 220 to 250 ft–lb (298 to 339 N–m).
Insert flange head screw through end yoke and stub
Position inner and outer bearing cups to axle hous-
7.
Position driveshaft cross to the end yoke. Install the
straps  to secure  driveshaft bearing  cross  to the  end
yoke. Torque bolts from  200 to 250 in–lb (22.6 to  28.3
N–m).
7.
8.
Pack bearings with lithium based grease.
Position outer bearing cone, wide end first, onto stub
axle. Press bearing onto stub axle  putting pressure on
inner race of bearing.
8.
Manual).
Lubricate driveshaft grease fittings  (see Operator’s
9.
housing with grease.
Insert stub axle  with bearing into  axle housing. Fill
9.
Secure drive shaft to transaxle shaft (Fig. 9):
A.  Align mounting holes  in driveshaft  with relief in
transaxle shaft.
10.Insert
NOTE: The stepped  end of bearing  spacer should be
positioned away from stub axle flange.
bearing spacer onto stub axle inside housing.
B.  Install cap screws, hardened washers, and flange
nuts to secure driveshaft  to transaxle shaft. Torque
fasteners from 35 to 42 ft–lb (47 to 57 N–m).
11.
Insert inner,  greased bearing, small  end first,  onto
stub axle inside housing.
10.Install
Service and Repairs Section of Chapter 7 – Chassis).
brake drum and wheel (see Brake Service in
IMPORTANT: The  bearing seal must be pressed  in
so it is flush with the end of the axle housing. The lip
of the seal must be toward the bearing.
11.
88
Tighten wheel nuts to a torque of 45 to 65 ft–lb (61 to
N–m).
12.Install
new seal over shaft and into housing with the
seal lip inward. Be careful not to damage the seal during
installation.
12.Lower
vehicle to ground.
Workman 3000/4000 Series
Page 6 – 13  Rev. B
Drive Train
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 302 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website