Toro 03126SL Rev C Service Manual Serial No 240000001 Above Workman 3000 4000

Front Brake
45
(61 to 88 N–m)
to 65 ft–lb
1
40 to 60 ft–lb
(54
to 81 N–m)
2
LOCTITE #680
3
4
5
6
23
22
SMALL SPACER
8
7
11
9
12
14
15
10
170
to 200 ft–lb
to 271 N–m)
13
(230
17
ACCESS HOLE
21
20
16
19
18
17
RIGHT
LOCTITE #271
FRONT
APPLY GREASE
TO SPLINES
Figure 5
1.
2.
3.
4.
5.
6.
7.
8.
Wheel nut (5 used per wheel)
Wheel and tire assembly
Brake drum
9.
Lock washer (4 used per brake)
17. Bearing assembly
18. Axle housing (RH shown)
19. Brake plate plug
10. Brake tube
11.  Cap screw
12. Flat washer
13. Brake hose retainer clip
14. Brake hose
15. Brake hose bracket
16. Constant velocity (CV) joint assembly
Stub axle
20. Front brake assembly (RH shown)
21. Wheel bearing spacer
22. Hardened washer
Lock washer (5 used per wheel)
Hex bolt (5 used per wheel)
Brake cable clip
23. Hex flange nut
Cap screw (4 used per brake)
Removal (Fig. 5)
Park vehicle on a level surface. Make sure engine is
5.  Pull stub axle and outer bearing cone from the axle
housing and the splined end of the CV joint. Make sure
wheel bearing spacer and small spacer  come out with
the stub axle.
1.
off. Engage parking brake and block rear wheels.
2.
Partially loosen front wheel lug nuts. Jack up and se-
NOTE:  It may be  necessary to remove the  brake as-
sembly from the axle housing for servicing some com-
ponents such as the brake cylinder assembly.
cure front wheel off the ground (see Jacking Instructions
in Operator’s Manual). Remove wheel  nuts and wheel
from the brake drum.
6.
If necessary, remove brake assembly as follows:
NOTE:  If the brake drum sticks to the brake shoes dur-
ing removal, loosen brake shoes from the drum by turn-
ing bolt adjuster through access hole in brake drum.
A.  Disconnect brake tube  (10) from  the brake as-
sembly. Plug  brake  tube to  prevent contaminants
from entering brake system.
3.
Remove brake drum from hub.
B.  Remove brake assembly from the  axle housing
by removing the four cap screws (8) and lock wash-
ers (9) from the housing.
4.
(22)
Remove hex flange nut  (23) and hardened washer
from the threaded shaft of the CV joint. Discard nut.
Front Wheel Drive (4WD)
Page 10 – 8    Rev. B
Workman 4000 Series
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 302 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website