Toro 03126SL Rev C Service Manual Serial No 240000001 Above Workman 3000 4000

Assembly (Fig. 61)
1.
Clean all parts thoroughly of all dirt and debris to pre-
vent damage to the bidirectional clutch and transaxle.
2.
Place garter  spring around  the  cage and  into the
groove (Fig. 66).
1
3.
the cam (Fig. 67).
Place thrust bearing, thrust washer, and spring onto
2
4.
Insert cam  with thrust bearing,  thrust washer,  and
spring into the cage (Fig. 68).
Figure 66
1.
Garter spring
2.
Cage
NOTE:  Rollers must be replaced as a complete set.
5.
garter spring  fits snuggly into  the groove of  all rollers
(Fig. 68).
Insert rollers into  the slots of  the cage. Make  sure
3
2
NOTE:  Both bearings must be replaced as a set.
6.
If the  ball bearings  (4) were  removed, press   new
bearings into the housing and race (5).
1
4
7.
If the oil seal (13) was removed, press new seal into
the housing and race (5). Make sure the metal side of the
seal faces out from the housing.
Figure 67
Installation (Fig. 61)
1.
2.
Thrust bearing
Thrust washer
3.
4.
Spring
Cam
1.
Clean adapter plate (14) thoroughly of all dirt and de-
bris to prevent  damage to the bidirectional  clutch and
transaxle.
1
2.
If the adapter plate (14) was removed from the trans-
axle, install as follows:
4
A.  Make sure contact surfaces between the adapter
plate and transaxle are free of dirt, debris, and oil.
2
B.  Apply Loctite  #59375 black  silicone sealant  or
equivalent to the back side of the adapter plate.
3
C. Secure  adapter plate  to the transaxle  with four
screws (15). Make  sure not to  get sealant into the
threaded holes of the transaxle.
Figure 68
1.
2.
Cam
Cage
3.
4.
Roller
Garter spring
3.
Coat front  drive shaft  (19) and  adapter plate  (14)
lightly with Dexron III ATF. Slide cage and roller assem-
bly as a complete assembly (see Fig. 62) slowly onto the
front drive shaft. Make sure large base end of the cage
is installed first.
4.
Position housing and race (5) over the cage and roll-
er assembly. Make sure assembly parts are positioned
properly by  pushing the  clutch towards  the transaxle
and feeling for spring (11) compression.
Front Wheel Drive (4WD)
Page 10 – 34
Workman 4000 Series
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 302 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website