Toro 03126SL Rev C Service Manual Serial No 240000001 Above Workman 3000 4000

Removal (Fig. 4)
1.
Remove knobs from control levers, then remove cen-
ter console shift boot and control plate (Fig. 5).
2.
Remove  three screws  (Item 18)  and  cable clamp
(Item 19) that secure shift cables to lever support.
3.
Remove cotter  pin and  clevis pin that  secure shift
cable clevis to shift link (Item 10)  on shifter in operator
platform.
4.
Loosen jam nut that retains clevis to shift cable and
remove clevis from cable.
1
2
5.
Remove shift cable from transaxle shift lever (Fig. 7):
Figure 5
A.  Remove cotter pin and clevis pin that secure shift
cable to shift lever on transaxle.
1.
Shift boot
2.
Control plate
B.  Loosen jam nuts on bulkhead fitting of cable.
C. Disconnect cable from shift lever.
.390
(9.9
to .510 in.
to 13 mm)
6.
Note routing of shift cable and location of cable ties
used to secure cable. Slide shift  cable from lower shift
boot and remove cable from vehicle.
4
Installation (Fig. 4)
3
2
1
1.
Route cable in same location as before.
Figure 6
1.
2.
Clevis
Shift cable
3.
4.
Clamp
Shift stop bolt
2.
Install cable clevis on shift cable. Adjust cable clevis
as shown in Figure 6. Tighten jam nut to secure clevis to
cable.
3
3.
Connect shift cable to shift link (Item 10) on shifter in
operator platform by inserting clevis pin (Item 8) from the
passenger side, then install cotter pin.
4.
Secure shift cables to lever support with cable clamp
(Item 19) and three screws (Item 18).
3
2
5.
Spread jam nuts on bulkhead fitting of cable (Fig. 7).
With  cable properly  routed to  transaxle,  install cable
bulkhead fitting to shift cable mount bracket on transaxle
and tighten jam nuts.
1
Figure 7
3.
6.
shift cables to vehicle.
Install cable  ties in the  original locations to  secure
1.
2.
First–Reverse
2nd–3rd
Bulkhead jam nut
7.
Adjust shift cables (see Operator’s Manual) and se-
cure cable clevis to transaxle shift  lever with clevis pin
and cotter pin.
8.
Check adjustment of shift stop bolts. Move shift lever
forward until lever stops. Hold lever in stopped position
and adjust  stop bolt  so that  head just  contacts lever.
Tighten hex nut on stop bolt.
9.
Install  shift  boot,  control  plate  and  control  lever
knobs.
Workman 3000/4000 Series
Page 6 – 11
Drive Train
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 302 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website