Toro 09172SL Models 30857 30858 Groundsmaster 4500 D 4700 D Service Manual

NOTE:  Gear Pump P4 supplies oil flow for the engine
cooling fan circuit.
IMPORTANT: The gear pump is a positive displace-
ment type. If pump flow is completely restricted or
stopped, damage to the pump, tester or other com-
ponents could occur.
Procedure for Gear Pump P4 Flow Test
1.
Make sure hydraulic oil is at normal operating tem-
peraturebyoperatingthemachineforapproximatelyten
minutes. Make sure the hydraulic tank is full.
8.
While watching  pressure gauge, slowly  close flow
control valve  on tester until  1000 PSI (69 bar)  is ob-
tained on pressure gauge. Verify engine speed contin-
ues to be correct (2870 RPM).
(10)
2.
Park machine  on  a level  surface with  the cutting
decks lowered and off. Make sure engine is off and the
parking brake is engaged.
9.
be approximately 6.3 GPM (23.8 LPM).
For a pump in good condition, flow indication should
3.
Raise hood to allow access to pump assembly.
10.Fully
open flow control valve on tester and then shut
engine off. Record test results.
CAUTION
11.
If the flow  is lower than 5.3 GPM  (20.1 LPM) or a
pressure of 1000 PSI  (69 bar) could not be obtained,
check for restriction in pump intake line. If intake line is
not restricted, remove gear pump and repair or replace
as necessary.
Prevent personal injury and/or damage to equip-
ment. Read all WARNINGS, CAUTIONS and Pre-
cautions for Hydraulic Testing at the  beginning
of this section.
12.Lower
and secure hood after testing is completed.
4.
Thoroughly clean junction of hydraulic hose and fit-
ting in gear pump section P4 (Fig. 55). Disconnect hy-
draulic hose from fitting.
RIGHT
FRONT
IMPORTANT: Make sure  that the oil flow  indicator
arrow on the tester is showing that the oil will flow
from the gear pump fitting, through  the tester and
into the disconnected hose.
2
5.
Install tester with pressure gauge and flow meter in
1
series with  the disconnected  hose and fitting  in gear
pump section P4. Make sure the flowcontrol valveon
the tester is fully open.
6.
speed. Check for hydraulic leakage and correct before
proceeding with test.
After installing  tester, start  engine and  run at idle
7.
gage the cutting decks.
Move throttle to full speed (2870 RPM). DO NOT en-
Figure 55
1.
Gear pump
2.
Pump section P4 hose
Groundsmaster 4500--D/4700--D
Page 4 -- 67
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 298 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website