Component Testing
For accurate resistance and/or continuity checks, elec-
trically disconnect the component being tested from the
circuit (e.g. unplug the ignition switch connector before
checking continuity on the switch terminals).
CAUTION
When testing electrical components for continu-
ity with a multimeter (ohms setting), make sure
that power to the circuit has been disconnected.
NOTE: For engine component testing information, see
Engine,
V2403--M--T--E3B at the end of Chapter 3 -- Kubota Die-
sel Engine.
the
Kubota
Workshop
Manual,
Diesel
Ignition Switch
The ignition (key) switch on the console arm has three
7. After testing is completed, connect the wire harness
connector to the ignition switch.
(3)
positions (OFF, ON/PREHEAT and START).
Testing
8. Assemble console arm (see Console Arm Assembly
in the Service and Repairs section of Chapter 7 -- Chas-
sis).
1.
Before disconnecting the ignition switch for testing,
the switch and its circuit wiring should be tested as a
TEC input with the Diagnostic Display (see Diagnostic
Display in the Troubleshooting section of this chapter).
If the Diagnostic Display verifies that the ignition switch
and circuit wiring are functioning correctly, no further
switch testing is necessary. If, however, the Display de-
termines that the ignition switch and circuit wiring are
not functioning correctly, proceed with test.
2
2.
Make sure ignition switch is OFF. Remove key from
ignition switch.
3.
switch (see Console Arm Disassembly in the Service
and Repairs section of Chapter 7 -- Chassis).
Disassemble console arm to gain access to ignition
4.
Disconnect wire harness electrical connector from
the ignition switch.
1
5.
The ignition switch terminals are identified as shown
in Figure 13. The circuit logic of the ignition switch is
shown in the chart below. With the use of a multimeter
(ohms setting), the switch functions can be tested to de-
termine whether continuity exists between the various
terminals for each switch position. Verify continuity be-
tween switch terminals. Replace switch if testing identi-
fies that switch is faulty.
Figure 12
1.
Console arm
2.
Ignition switch
ON/PREHEAT
45
o
45o
OFF
START
POSITION
OFF
CIRCUIT
NONE
A
F
ON/PREHEAT
START
B + C + F, D + E
A + B + C
B
C
E
D
FRONT VIEW
REAR VIEW
6.
If ignition switch tests correctly and circuit problem
still exists, check wire harness (see Electrical Schemat-
ics and Wire Harness Drawings in Chapter 9 -- Foldout
Drawings).
Figure 13
Groundsmaster 4500--D/4700--D
Page 5 -- 15
Electrical System
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 30857, Toro Groundsmaster 30858, Toro Groundsmaster 4500 D, Toro Groundsmaster 4700 D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)