Adjustable Fitting (Fig. 6)
Make sure all threads and sealing surfaces of fitting
1.
and component port are free of burrs, nicks, scratches
or any foreign material.
2.
ommended that the O--ring be replaced any time the
connection is opened.
As a preventative measure against leakage, it is rec-
Lock Nut
3.
Fitting threads should beclean withno lubricantapplied.
Lightly lubricate the O--ring with clean hydraulic oil.
Back--up Washer
4.
the back up washer is not loose and is pushed up as far
as possible (Step 1 in Figure 7).
Turn back the lock nut as far as possible. Make sure
O--ring
Figure 6
IMPORTANT: Before installing fitting into port, de-
termine port material. If fitting is to be installed into
an aluminum port, installation torque is reduced.
5.
until the washer contacts the face of the port (Step 2).
Install the fitting into the port and tighten finger tight
Step 1
Step 2
Step 3
Step 4
6.
therequiredamount,butnomorethanonefullturn(Step
3).
To put the fitting in the desired position, unscrew it by
7.
Hold the fitting in the desired position with a wrench
and use a torque wrench to tighten the fitting to the rec-
ommended installation torque shown in Figure 5. This
tightening process will require the use of an offset
wrench (e.g. crowfoot wrench). Use of an offset wrench
will affect torque wrench calibration due to the effective
length change of the torque wrench. Tightening torque
whenusingatorquewrenchwithanoffsetwrenchwillbe
lower than the listed installation torque (see Using a
Torque Wrench with an Offset Wrench in the Torque
Specifications section of Chapter 2 -- Product Records
and Maintenance).
Figure 7
8.
If a torque wrench is not available, or if space at the
port prevents use of atorque wrench, an alternate meth-
od of assembly is the Flats From Finger Tight (F.F.F.T.)
method. Hold the fitting in the desired position with a
wrench and, if port material is steel, tighten the lock nut
with a second wrench tothe listed F.F.F.T (Step 4). Ifport
material is aluminum, tighten fitting to 60% of listed
F.F.F.T.
Size
F.F.F.T.
4
6
8
10
12
16
(1/4 in. nominal hose or tubing)
(3/8 in.)
(1/2 in.)
(5/8 in.)
(3/4 in.)
(1 in.)
1.00 + 0.25
1.50 + 0.25
1.50 + 0.25
1.50 + 0.25
1.50 + 0.25
1.50 + 0.25
Workman HD Series
Page 9 -- 7
Hydraulic System
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 09173SL |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)