16.Put
axle with a floor jack or suspend transaxle from vehicle
frame rails.
blockingunderengineforsupport.Supporttrans-
1
1
17.Remove
isolation mount assemblies and transaxle
mounts (Fig. 16).
18.Remove
driveshaft clamp bolts, then slide transaxle
side--to--side to disconnect each driveshaft from axle
shafts on transaxle.
19.Remove
engine. Note location of washers and harness brackets.
cap screws securing clutch bell housing to
2
2
20.Carefully
pull transaxle back to disengage transaxle
input shaft from clutch. Use floor jack to lower transaxle
and slide out rear of vehicle under the frame.
Figure 16
1.
Transaxle mount
2.
Driveshaft
21.Note
location and retrieve two (2) dowel pins from
bell housing.
2
Transaxle Installation (Fig. 12)
3
1
1.
To install the transaxle, perform Transaxle Removal
procedure in reverse order noting the following:
IMPORTANT: Workman HD (air cooled, gasoline en-
gine)vehiclesrequireapplicationofsiliconesealant
to mating surface of bell housing and clutch adapter
plate on engine. This will prevent dirt and debris
from getting into bell housing and damaging clutch
or release bearing.
3
4
A. When installing driveshafts to transaxle, apply
antiseize lubricant to transaxle shafts. Align mount-
ing holes in driveshaft with relief in transaxle shaft.
Install cap screws, hardened washers and flange
nuts to secure driveshaft to transaxle shaft. Torque
fasteners from 40 to 45 ft--lb (55 to 61 N--m).
Figure 17
3.
4.
1.
2.
Bell housing
Cap screw (6 used)
Harness bracket
Dowel pin (2 used)
230
(26 to 27 N--m)
to 240 in--lb
B. Before installing two (2) shift levers and shift arm
onto transaxle shafts, thoroughly clean tapers of
shafts, shift levers and shift arm. Apply Loctite #680
to threads and tapers of shafts. Secure levers and
shift arm by torquing nut from 230 to 240 in--lb (26 to
230 to 240 in--lb
(26
to 27 N--m)
27
fer into transaxle (Fig. 18).
N--m) while holding lever to prevent torque trans-
Apply Loctite #680
to threads and tapers
2.
the Dexron III oil (see Operator’s Manual). Check for oil
leaks and repair as necessary.
Install a new hydraulic oil filter and fill transaxle with
3.
differential lock cable (see Operator’s Manual).
Adjust clutch pedal, shift cables, high--low cable and
4.
Cable Adjustment in the Adjustments section of this
chapter).
If equipped with PTO, adjust PTO cable (see PTO
Figure 18
Drive Train
Page 6 -- 18
Workman HD Series
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 09173SL |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)