Toro 09173SL Workman HD Series Service Manual

2.
Check pilot bearing (item 23) for smooth rolling and
7.  Secure engine to engine mount with four (4) flange
nuts (item 34) and flange head screws (item 36).
noise. Check (sealed) bearing for grease leakage. Re-
place bearing if necessary. Remove pilot bearing from
flywheelbybackingoutsocketheadscrew(item22)that
attaches flywheel to crankshaft. Do not reuse bearing if
it has been removed.
8.
Connect choke cable (item 33) to choke lever on en-
gine (Fig. 7).
9.
Connect  accelerator  cable ball  joint  (item  11) to
throttle lever on engine (Fig. 7). Secure cable to throttle
bracket with jam nuts.
Engine Installation (Fig. 5)
1.
23)
Install flywheel (item 20)  and/or pilot bearing (item
ifremoved.Torquesocketheadscrew(item22)from
10.Connect
nents.
wire harness connectors to engine compo-
35
to 40 ft--lb (48 to 55 N--m) to secure flywheel to en-
gine crankshaft.
11.
Connect fuel hose to fuel pump  on engine and se-
cure with hose clamp.
2.
If pressure plate and clutch disc were removed from
engine, see Clutch Service in the Service and Repairs
section ofChapter 6 -- Drive Trainforassembly process.
12.Secure
ness (item 41) to starter solenoid stud on engine.
positive cable (item 37) and fusible link har-
3.
from engine, apply  antiseize lubricant on engine  stub
shaft before installing pulley.
If hydraulic pump drive pulley (item 3) was removed
13.Install
haust System Installation in this section).
the muffler  and exhaust  manifold (see  Ex-
14.Install
rect oil.
a new engine oil filter. Fill engine with the cor-
hydraulic pump drive belt to pump and engine
4.
5.
son should operate hoist and a second person should
helpguideenginetomachine.Alignsplinesontransaxle
input shaft and clutch while moving engine to bell hous-
ing on transaxle.
Place two (2) dowel pins (item 48) in bell housing.
Use lift or hoist to install engine to chassis. One per-
15.Install
pulleys. Adjust belt tension (see Operator’s Manual).
16.Connect
cables to the battery.
positive (+) and  then negative (--) battery
6.
six (6) cap screws (item 19) and two (2) harness brack-
ets (item 46).
Secure bell housing to clutch adapter on engine with
17.Check
18.Lower
operation of accelerator and choke cables.
bed or install bed or attachment(s).
Kohler Gasoline Engine
Workman HD
Page 5 -- 12
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 306 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website