Removal (Fig. 9)
Park vehicle on a level surface, stop engine, engage
parking brake and remove key from the ignition switch.
Allow engine and radiator to cool.
Installation (Fig. 9)
1.
1. If radiator assembly was disassembled, install com-
ponents to radiator using Figure 10 as a guide. Make
sure that clearance exists between shroud and fan at all
points.
2.
Raise or remove the bed or other attachment(s). If
bed is raised, place safety support on lift cylinder.
2. Remove plugs from radiator openings and hoses
placed during the removal procedure.
3.
Unlatch and remove radiator screen from front of ra-
diator.
3. Positionradiatorassemblytotheradiatormount.Se-
cure radiator assembly to the vehicle with removed
flange head screws, flat washers and flange nuts.
4.
Ifvehicle isequipped withhigh flowhydraulics kit,ro-
tate oil cooler latches and place oil cooler away from ra-
diator.
4. Connect reservoir hose (item 6) to the radiator filler
neck. Secure hose with hose clamp.
CAUTION
5. Connect upper and lower hoses to the radiator. Se-
cure hoses with hose clamps.
Do not open radiator cap or drain coolant if the
radiator or engine is hot. Pressurized, hot cool-
ant can escape and cause burns.
6. Connect wire harness connector to radiator fan.
7. Fill radiator with coolant.
Ethylene--glycol antifreeze is poisonous. Dis-
pose of coolant properly or store it in a properly
labeled container away from children and pets.
8. If vehicle is equipped with high flow hydraulics kit,
position oil cooler to radiator and secure in place.
9.
Install and latch the radiator screen.
5.
6.
Remove the radiator cap.
10.Lower
or install bed or other attachment(s).
Drain radiator into a suitable container by discon-
necting lower radiator hose from the radiator.
6
4
7.
8.
Disconnect upper radiator hose from the radiator.
Disconnect reservoir hose (item 6) from the radiator
1
9
8
5
filler neck.
5
9.
Disconnect wire harness connector from radiator
fan.
10.Detach
radiator assembly from radiator mount:
A. Remove two (2) flange head screws and flat
washers that secure the top of the radiator assembly
to the mount.
7
3
6
2
B. Remove two (2) flange head screws and flange
nuts that secure the bottom of the radiator assembly
to the mount.
Figure 10
1.
2.
3.
4.
5.
Radiator
Electric fan
Shroud
6.
7.
8.
9.
Nut (7 used)
Screw (4 used)
Lower mount plate
Radiator cap
11.
Carefully separate radiator assembly from mount
and remove from vehicle.
Spring latch (2 used)
Flange screw (7 used)
12.Plug
all radiator and hose openings to prevent con-
tamination.
13.If
necessary, remove components from radiator us-
ing Figure 10 as a guide.
Workman HDX--D
Briggs/Daihatsu Diesel Engine
Page 4 -- 13
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 09173SL |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)