8.
lever (see Engine Throttle Bracket Disassembly in this
section). Position accelerator cable away from engine.
Disconnect accelerator cable ball joint from throttle
16.Remove six (6) cap screws that secure clutch bell
housing to engine. Note location of two (2) harness
brackets as caps screws are being removed (Fig. 18).
17.Use
ahoistorlifttoremoveenginefromchassis.One
CAUTION
person should operate hoist or lift and a second person
should help guide engine out of chassis. Move engine
forward before lifting to disengage transaxle input shaft
from clutch.
Do not open radiator cap or drain coolant if the
radiator or engine is hot. Pressurized, hot cool-
ant can escape and cause burns.
18.Note location and retrieve two (2) dowel pins from
bell housing (Fig. 18).
Ethylene--glycol antifreeze is poisonous. Dis-
pose of coolant properly or store it in a properly
labeled container away from children and pets.
19.If
necessary, remove gear pump from engine mount
(see Gear Pump Removal in the Service and Repairs
section of Chapter 9 -- Hydraulic System).
9.
able container by disconnecting lower radiator hose
from the radiator.
Remove the radiator cap. Drain radiator into a suit-
20.If
21.If
necessary, remove engine mount from engine.
necessary, remove coupler components from en-
gine pulley using Figure 15 as a guide.
10.Loosen
hose clamps and remove upper and lower
radiator hoses from engine. Remove R--clamp (item 35)
that secures lower radiator hose to engine mount. Posi-
tion radiator hoses away from engine.
22.If
sary, see Clutch Disassembly and Inspection in the Ser-
vice and Repairs section of Chapter 6 -- Drive Train.
pressure plate and clutch disc removal is neces-
11.
Removeallclampsandcabletiesusedtoattachwire
harness, hoses or cables to the engine.
2
3
12.On
4WD vehicles, remove differential drive shaft
4
(see Differential Driveshaft Removal in the Service and
Repairs section of Chapter 10 -- Front Wheel Drive
(4WD)).
1
2
3
CAUTION
Before performing any service or repair on hy-
draulic system components, relieve system
pressure to avoid injury from pressurized hy-
draulic oil. Rotate the steering wheel in both di-
rections, make sure that the bed is lowered onto
the bed support and operate any other hydraulic
accessories.
2
4
NOTE: Ifvehicle is equipped with High Flow Hydraulics
Kit, label hydraulic hoses for assembly purposes.
Figure 18
1.
2.
Bell housing
Cap screw (6 used)
3.
4.
Harness bracket
Dowel pins (2 used)
13.Thoroughly
clean junction of gear pump fittings and
hydraulic hoses. Disconnect hydraulic hoses from gear
pump. Install caps or plugs in hoses and pump fittings
to prevent contamination and leakage of hydraulic oil.
14.Put
blockingundertransaxletopreventthetransaxle
from moving during engine removal.
15.Loosen
and remove two (2) flange nuts, snubbing
washers and cap screws that secure engine mount to
engine support (Fig. 17).
Briggs/Daihatsu Gasoline Engine
Page 3 -- 20
Workman HDX
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 09173SL |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)