Toro 98957SL Rev B Sand Pro 2020 3020 5020 Service Manual

Traction Pump Disassembly
1.
Charge Pump Disassembly).
Remove charge pump from  variable housing (see
7
6
2.
(see Shaft Seal Removal).
Remove lip  seals  from shaft  and trunnion  shafts
5
1
IMPORTANT: All exposed surfaces are critical. Use
caution to avoid damage to exposed surfaces.
2
3
3.
cap. Loosen cap screws evenly to prevent distortion of
parts (Fig. 45).
Remove four cap screws and washers from the end
8
9
4
A.  Internal spring loading should cause the end cap
to separate slightly from the variable housing. If sep-
aration does  not occur  during loosening, tap  end
cap with a soft hammer until parts separate.
Figure 45
1.
2.
3.
4.
5.
Cap screw
Washer
6.
7.
8.
9.
Locating pin
O–rings
End cap gasket
Needle bearing
End cap
Variable housing
Valve plate
B.  Make sure valve plate does not fall and become
damaged. Discard O–rings and end cap gasket.
4.
Remove end cap and valve plate together from the
2
variable housing. If valve plate remains on the cylinder
block, remove it. Remove locating pin from the end cap
(Fig. 45).
5
NOTE:  The pistons may slide out of the cylinder block.
Piston placement in the bores requires no special orien-
tating. Do not disassemble spring or other parts from the
center bore of the cylinder block.
1
3
4
5.
Remove cylinder block assembly from the variable
housing. Remove thrust  plate from the counterbore in
the face of the swashplate (Fig. 46).
6
Figure 46
4.
IMPORTANT: Make sure not to damage the face sur-
face on the cavity side of the variable housing.
1.
2.
3.
Cylinder block
Piston assemblies
Thrust plate
Variable housing
Cylinder block assembly
Spider
5.
6.
6.
Position variable housing so the large cavity faces
up (Fig. 47).
11
NOTE:  The variable housing has a cast recess that al-
lows the  spring pins to  be driven  free of the  trunnion
shaft and control shaft.
8
3
9
2
7.
Drive spring pin out of the trunnion shaft and control
5
shaft using a 3/16 inch diameter drift punch (Fig. 47).
6
7
1
10
8.
Drive control and trunnion shafts outward and out of
the swashplate bore. Shafts remove easily once clear of
the swashplate bore (Fig. 47).
4
9.
Remove swashplate from the variable housing. Re-
move retaining  ring from  the variable  housing. Press
shaft out with bearing and retaining ring. Remove retain-
ing ring and bearing from the shaft (Fig. 47).
Figure 47
1.
2.
3.
4.
5.
6.
Variable housing
Spring pins
Control shaft
Trunnion shaft
Swashplate
Shaft
7.
8.
9.
10.  Needle bearing
11.  Journal bearing
Retaining ring
Ball bearing
Retaining ring
Hydraulic System (Rev. A)
Page 4 – 52
Sand Pro 2020/3020/5020
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 170 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website