Toro 98957SL Rev B Sand Pro 2020 3020 5020 Service Manual

8.
curing the hydraulic motor the fork.
Remove both socket head screws and lock nuts se-
3.   Secure lug nuts to drive studs. Torque nuts from 45
to 55 ft–lb (6.2 to 7.6 kg–m).
4.
spindle shaft so the locking collar faces the wheel.
Slide  flangette  and  bearing   assembly  onto  the
WARNING
5.
the front fork.
Position hydraulic motor,  wheel, and flangettes  to
Before jacking up the machine, review and follow
Jacking Instructions in Chapter 1 – Safety.
6.
Lower front fork slowly making sure flangettes and
front wheel motor fit snugly into the fork.
IMPORTANT: Support wheel and  motor when jack-
ing up the front fork to prevent dropping and dam-
aging the motor.
A.  Secure flangettes to  the fork with  cap screws,
bearing tab, and locknuts.
9.
flangettes can be removed from the fork. Remove flan-
gettes, spindle, wheel, and motor from the fork.
Jack up  fork slowly  until the  hydraulic motor and
B.  Secure hydraulic  motor  to  the front  fork  with
socket head screws and lock nuts.
7.
draulic motor are positioned correctly into the fork. Tight-
en fasteners properly.
Lower fork completely. Make sure flangette and hy-
10.
spindle. Do not further disassemble flangettes and bear-
ing.
Slide  flangettes  and bearing  assembly  from  the
8.
Install set  screws to locking collar.  Torque set screws
from 65 to 80 in–lb (74.9 to 92.2 kg–cm).
Apply Loctite 242 or equivalent to both set screws.
11.
wheel  from  the   drive  studs  and  spindle.  Separate
spindle from drive studs and wheel hub.
Remove four lug nuts from the drive studs. Remove
9.
and fittings
Remove caps  or plugs  from  disconnected hoses
12.
shaft of the hydraulic motor. Pull motor shaft from hub.
Remove woodruff key from the motor shaft.
Lock wheel hub in a vice. Remove lock nut from the
10.
Install O–rings and 45o hydraulic fittings to the hy-
draulic motor. Torque fittings from 72 to 80 ft–lb (9.9 to
Installation (Fig. 29)
11
kg–m).
1.
Lock wheel hub in a  vice. Install woodruff key into
11.
Connect hydraulic hoses from 45o hydraulic fittings.
torque hose connections from 25 to 30 ft–lb (3.5 to 4.1
kg–m).
the hydraulic motor shaft. Slide motor shaft into hub and
secure with lock nut. Torque lock nut from 200 to 400 ft–
lb (27.7 to 55.3 kg–m).
12.
System).
Charge  hydraulic system  (see  Charge Hydraulic
2.
Install spindle to drive studs and wheel hub. Insert
spindle and drive studs through wheel. Make sure valve
stem and hydraulic motor are on the  opposite sides of
the wheel.
Sand Pro 2020/3020/5020
Page 4 – 57
Hydraulic System (Rev. A)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 170 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website