Toro 98957SL Rev B Sand Pro 2020 3020 5020 Service Manual

Removal (Fig. 25)
Before removing any parts from the hydraulic sys-
tem, park machine on a level  surface, engage parking
brake, lower attachment, and stop engine.
Installation (Fig. 25)
1.
1.   Make  sure lift valve, hydraulic  hoses, fittings, and
tubes are cleaned thoroughly.
2.
13)
ing.
Reinstall O–rings (31) and hydraulic fittings (4 and
to the lift valve. Observe match marks when tighten-
CAUTION
3.
Position lift valve (14) to the frame. Insert four cap
screws (15) through the frame and lift valve. Screw lock
nuts (11) to the bottom two cap screws (15).
Operate all hydraulic controls to relieve system
pressure and avoid injury  from pressurized hy-
draulic oil. Controls  must be operated  with the
ignition switch in OFF. Remove key from the igni-
tion switch.
4.   Position lift lever (6) through the frame and attached
pivot bracket (9) and other attached parts onto the  top
two cap screws (15). Screw lock nuts (11) to the top two
cap screws (15). Tighten all four lock nuts.
2.
Remove cover from the midsection of the machine.
Pivot seat up. Unscrew knob (5) from lift lever (6).
5.
Secure  pivot (18)  to the  lift  valve stem  with cap
screw (7) and lock nut (10). Tighten fasteners.
3.
Remove lift valve shroud (2) as follows:
6.
hoses, tubes, and fittings
Remove  caps  and plugs  from  the  disconnected
A.  Remove self tapping screw (16) from the shroud
and frame.
7.
Reconnect hydraulic tube (34) to the 90o hydraulic
fitting (4). Reconnect swivel run T–fitting (12) to the 45o
hydraulic fitting  (13). Reconnect both hydraulic  hoses
B.  Remove both cap screws (3) and lock nuts (38)
securing the shroud, lift lever guide (36), and valve
lever latch (20) to the frame.
(30)
with O–rings (29) to the lift  valve. Tighten all con-
C. Lift shroud from the frame.
nections.
4.
Clean lift valve (14) and all hydraulic fittings, tubes,
8.   Attach lift valve shroud (2) as follows:
and hoses attached to it thoroughly.
A.  Position valve lever latch (20) and lift lever guide
(36) over the lift lever and onto the frame.
5.
Label all hydraulic connections for reassembly.
6.
Disconnect both hydraulic  hoses (30) from  the lift
B.  Insert both cap screws (3) to the shroud.
valve. Disconnect swivel run T–fitting (12) from the 45o
C. Lower  shroud  around  lift  lever  (6)  and  onto
frame. Make sure cap  screws go through lift lever
guide (36) and valve lever latch (20).
hydraulic  fitting (13).  Disconnect  hydraulic  tube (34)
from the 90o hydraulic fitting (4). Allow hoses, tubes, and
fittings to drain into a suitable container.
D. Attach  lock  nuts  (38) to  cap  screws. Do  not
tighten fasteners.
7.
and fittings to prevent contamination.
Put caps  or plugs on  disconnected hoses, tubes,
E.  Reinstall self tapping screw  (16) to the shroud
and frame. Tighten screw.
8.
the pivot (18) to the lift valve stem.
Remove cap screw (7)  and lock nut (10) securing
9.
Screw knob (5) onto the lift lever (6). Hand tighten.
9.
Remove four cap screws (15) and lock nuts (11) se-
curing the pivot  bracket (9) to the lift  valve and the lift
valve to the frame. Separate lift valve from the frame.Do
not further disassemble parts assembled to the lift
lever.
10.
System).
Charge  hydraulic system  (see  Charge Hydraulic
11.
Run machine and check lift valve, hydraulic hoses,
tubes, and fittings for leaks. Tighten as necessary.
IMPORTANT: Match mark positions of hydraulic fit-
tings  (4 and  13) relative  to  their ports  on the  lift
valve.
12.
13.
Adjust lift lever (6) (see Adjust Lift Lever).
Reinstall cover to the midsection of the machine.
10.
Remove remaining hydraulic fittings (4 and 13) and
O–rings (31) from the lift valve.
Sand Pro 2020/3020/5020
Page 4 – 35
Hydraulic System (Rev. A)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 170 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website