Toro 98957SL Rev B Sand Pro 2020 3020 5020 Service Manual

NOTE:  The rotor set consists  of the rotor (19), vanes
and stator  (21). Rotor  set components may  be-
(20),
come disassembled during service procedures. Do not
service separately.
NOTE:  It may be necessary to turn one alignment stud
out of the housing (3) temporarily to assemble rotor set
over the drive link (13).
NOTE:  The rotor  set rotor counterbore  side must  be
down against wear plate for drive link clearance and to
maintain the original rotor–drive link spline contact. A ro-
tor set without a  counterbore and that was not  etched
before disassembly can  be reinstalled using the  drive
link spline pattern on the rotor splines if apparent, to de-
termine which side  was down. The  rotor set seal  ring
groove faces toward the wear plate (18).
Figure 79
Figure 80
Figure 81
Figure 82
13.
Install assembled rotor set onto wear plate (18) with
rotor (19) counterbore and seal ring side down. Splines
should mesh with the drive link (13) splines (Fig 79).
14.
(20)
If disassembled  rotor (19), stator (21),  and vanes
cannot be readily  assembled by hand,  assemble
with the following procedures:
A.  Place stator (21) onto wear plate (18) with seal
ring (5) side down. Be sure the seal ring is in place
(Fig. 80).
B.  If assembly alignment  studs are not  being uti-
lized, align stator (21) bolt holes with wear plate (18)
and housing (3) bolt holes.  Screw two cap screws
(14)
finger tight  into bolt holes approximately  180
degrees apart to  retain stator and  wear plate sta-
tionary.
NOTE:  If the manifold  (22) side of the  rotor (19) was
etched  during   wheel  motor  disassembly,   this  side
should be up. If the rotor is not etched and does not have
a counterbore, use the drive link spline contact pattern
apparent on the rotor splines to determine the rotor side
that must be against the wear plate.
C. Place rotor (19) with counterbore down, if appli-
cable, into stator (21), and then onto wearplate (18)
so rotor  splines mesh  with drive  link (13) splines
(Fig. 81).
IMPORTANT: Do  not force  rotor vanes into  place,
the coating  applied  to stator  vane pockets  could
shear off.
D. Assemble six vanes (20), or as many vanes that
will readily assemble  into the stator  vane pockets
(Fig. 82).
Hydraulic System (Rev. A)
Page 4 – 68
Sand Pro 2020/3020/5020
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 170 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website