Toro 98957SL Rev B Sand Pro 2020 3020 5020 Service Manual

Upper Steering Disassembly (Fig. 13 and 14)
6
5
NOTE:  The front fork and steering  assemblies on the
SP 2020 and  SP 3020 are almost  identical. However,
there are differences in the construction of the front fork,
chain guide, chain bracket, and the number of steering
washers.
7
2
8
4
1.
stop engine,  engage parking  brake, and  remove key
from the ignition switch.
Park machine on a level surface, lower attachment,
2
1
3
2.
Remove hood  from the  dash panel  and machine
(see Hood and Dash Panel Removal).
Figure 15
NOTE:  The starter solenoid must be removed from the
frame to allow separation of the upper and lower steer-
ing shafts from the steering knuckle. Removal is not re-
quired for removal of the front fork.
1.
2.
3.
4.
Starter wire
Battery cable
5.
6.
7.
Steering
Lock   nut
R-clamp
8.      Cap
knuckle
screw
Starter
Self
solenoid
tapping
screw
3.
Remove black (negative) cable from the battery.
3
4.
Disconnect starter wire and battery cable from the
2
starter solenoid. Remove self tapping screws from  the
solenoid and  frame. Position  solenoid away  from the
steering knuckle (Fig. 15).
NOTE:  If disassembly above the steering knuckle is re-
quired, use the following procedure.
4
5.
Drive out  roll pin securing  upper steering shaft to
steering knuckle with drift punch.
6.
If it is required to remove the steering knuckle at this
time, drive out roll pin securing the lower steering shaft
to steering knuckle with drift punch.
Figure 16
7.
steering knuckle. If desired, pull  steering knuckle from
the lower steering shaft.
Pull  upper steering  shaft from  steering  post and
1.
2.
Hex flange head screws
Dash panel
3.   Steering post
4.
Position  upper  steering  shaft  down  through the
8.
dash panel to the steering post (Fig. 16).
Remove both hex flange head screws securing the
steering post into the steering knuckle. Align holes of the
shaft and steering knuckle and secure with roll pin.
9.
both R–clamps and steering post to the frame (Fig. 15).
Remove four  lock nuts  and cap  screws securing
5.   Secure  solenoid  to  the  frame  with   self  tapping
screws. Connect  starter wire and battery  cable to the
starter solenoid (Fig. 15).
10.
Pull dash  panel up and  back. Slide  steering post
from dash panel.
6.   Install  hood to  the dash panel  and machine  (see
Hood and Dash Panel Installation).
Upper Steering Assembly (Fig. 13 and 14)
7.
Install black (negative) cable to the battery.
1.
Position steering post through the dash  panel and
to the  frame. Secure  post and  both R–clamps to  the
frame with four cap screws and lock nuts (Fig. 15).
2.
Securedashpaneltothesteeringpostwithbothhex
flange head screws (Fig. 16).
3.
If removed, install steering  knuckle onto the lower
steering shaft with roll pin.
Wheels, Brakes, and Miscellaneous
Page 6 – 16
Sand Pro 2020/3020/5020
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 170 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website