Toro 98957SL Rev B Sand Pro 2020 3020 5020 Service Manual

Engine Installation (Fig. 37)
2
CAUTION
1
3
One person should operate the chain fall or hoist
while the other person guides the engine into the
frame.
1.
Install engine (16) to the engine base (15).
A.  Attach a hoist or chain fall to the engine.
Figure 41
IMPORTANT: Make sure not to damage the engine,
fuel and hydraulic lines, electrical harness, or other
parts while installing the engine.
1.
2.
Cap screw & lock washer
Pump mount
3.   Engine block
10.
Connect harness as follows (Fig. 38):
B.  Lower engine slowly onto the engine base.
A.  Connect blue wire to magneto terminal.
C. Insert  cap screw (13) through engine base and
engine  block.  Install  lock  washer (11)  onto  cap
screw with battery cable (26) and wire harness (43).
Screw hex nut (5) onto the cap screw.
B.  Connect blue wire with fusible link to voltage reg-
ulator.
C. Connect red/white wire to fuel solenoid.
D. Connect red (+) cable to starter.
D. Insert cap screws (13) through engine base and
engine block. Install flat washers (3) and screw hex
nuts (5) onto the cap screws. Do not tighten fasten-
ers at this time.
E.  Secure wire harness with cable tie to the starter.
Install and connect battery to the machine (see Bat-
11.
E.  Tighten all four fasteners securing the engine to
its base.
tery Service in Chapter 5 – Electrical Systems).
12.
13.
Install litter box to the fuel tank base.
Install engine cover. Pivot seat down.
2.
3.
Place square key on the engine shaft.
Positionpumpandpumpmounttotheengine.Make
sure engine hub slides onto the engine shaft and square
key (Fig. 40). Secure pump mount to  the engine block
with four cap screws and lock washers (Fig. 41).
4.
Tighten both set screws securing the engine hub to
the engine shaft (Fig. 40).
5.
Insert end of pump control rod into the pump lever.
Secure rod with cotter pin (Fig. 39).
6.
Connect  throttle control  cable  to  the swivel  and
choke control cable to the choke lever (see Throttle and
Choke Control Installation).
7.
Install air hose (33) to air cleaner cover (19). Secure
hose with hose clamp (34).
8.
Secure fuel hose (12) to the engine (16) with hose
clamp (28).  Remove clamp used  to prevent  drainage
from fuel hose (12). Open fuel shutoff located below the
fuel tank.
9.
Connect exhaust  tube and muffler  to the exhaust
manifold (see Muffler Installation).
Engine
Sand Pro 2020/3020/5020
Page 3 – 24
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 170 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website