Toro 98957SL Rev B Sand Pro 2020 3020 5020 Service Manual

3.
drostat. Observe match marks when tightening.
Reinstall O–rings  and hydraulic fittings  to the  hy-
14. Install  left fender and seat (see  Left Fender (Seat
Base) Installation in Chapter 6  – Wheels, Brakes, and
Miscellaneous). Install left and right  side panels to the
machine. Lower seat.
4.
fan (28) to the hydrostat shaft. Secure hub to shaft with
both set screws.
Install woodruff key (9) and fan hub (27) with cooling
15. Charge  hydraulic  system  (see Charge  Hydraulic
System).
5.
Secure hydrostat (8) to engine base with both sock-
et head screws (20) and lock nuts (10).
2
6.
Reinstall engine and hydrostat as follows:
CAUTION
1
One person should operate the chain fall or jack
while the other person guides the engine to  the
frame.
IMPORTANT: When  repositioning  the  engine and
hydrostat to the frame, make  sure not the damage
the cooling fan, wires, hoses, and cables.
Figure 37
1.
R–clamp
2.
Fuel hose
A.  Use jack or chain fall to position the front engine
mounts and  engine support to  the frame (Fig.  38
and 39).
1
2
B.  Secure engine mount to the frame with four cap
screws and flat washers (Fig. 39).
4
C. Secure  front engine  mounts to  the frame with
both cap screws, flat  washers, and lock nuts (Fig.
38).
D. Remove jack or chain fall from the engine base.
3
7.
tapping screw (Fig. 37).
Secure R–clamp and fuel hose to the frame with self
Figure 38
3.
4.
1.
2.
Lock nut
Flat washer
Cap screw
Engine mount
8.
Connect all six hydraulic hoses to fittings on the hy-
drostat. Remove clamps from hydraulic hoses (25 and
35)
9.
that prevented draining of the tank.
Tighten  both set  screws  (11) on  pump  hub (19)
enough to secure the hub to the shaft.
10.
Connect air  hose to  the  air cleaner.  Install lower
shroud to the cooler mount. Connect control rod to the
pump lever (Fig. 36).
2
3
1
1
11.
Secure black ground wire  and black battery cable
(negative) to the engine block with cap screw and lock
nut (Fig. 47).
Figure 39
12.
starter (Fig. 47).
Connect red positive cable  cable (solenoid) to the
1.
2.
Cap screw & flat washer
Engine support
3.
Engine base
13.
Connect wire harness as follows: connect blue wire
to the magneto terminal, connect blue wire  to the volt-
age regulator, and connect red/white wire to the fuel so-
lenoid (Fig. 45).
Hydraulic System (Rev. A)
Page 4 – 46
Sand Pro 2020/3020/5020
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 170 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website