Toro 98957SL Rev B Sand Pro 2020 3020 5020 Service Manual

E.  Grasp the output end of coupling shaft (11) with
locking pliers  or other appropriate  turning device.
Rotate coupling shaft, drive link (13), and rotor (19)
to seat the rotor and the assembled vanes (20) into
the stator (21). This rotation should create the nec-
essary clearance  to assemble  the seventh  or re-
23. Torque  both  plugs from  9 to  12  ft–lb (1.2  to  1.7
kg–m).
24.
Check motor shaft for rotation. Torque require to ro-
tate shaft should not exceed 50 ft–lb (6.9 kg–m).
maining
vanes.
Use
minimum
force
when
assembling the remaining vanes (Fig. 83).
F.  Remove the two assembled bolts (14) if used to
retain stator and wear plate.
NOTE:  The manifold (22) is made up of several plates
bonded together permanently to form an integral com-
ponent. The manifold surface that must contact the rotor
set has it’s series of irregular shaped cavities on the larg-
est circumference or circle around the inside diameter.
The polished impression left on the manifold by the rotor
set is another indication of which surface must contact
the rotor set.
Figure 83
15.
Apply clean petroleum  jelly to a  new seal ring (5)
and assemble it in the seal ring groove  in the rotor set
contact side of manifold (22).
16.
Assemble  the  manifold  (22)  over  the alignment
studs and drive link (13) and onto the rotor set. Be sure
the correct manifold surface is against the rotor set.
17.
Apply clean petroleum  jelly to a  new seal ring (5)
and insert it in the seal ring groove exposed on the man-
ifold (22).
18.
Assemble the commutator ring  (6) over alignment
studs onto the manifold (22) (Fig. 84).
Figure 84
19.
Assemble a new commutator seal (15) flat side up,
into commutator  (16) and assemble commutator  over
the end of drive link (13) onto manifold (22) with seal ring
side up.
20.
Assemble new seal ring (5) into end cover (24) and
assemble end cover over the alignment studs and onto
the commutator set.
21.
Assemble seven cap screws (14) and  screw them
in finger tight. Remove  and replace the two alignment
studs with bolts after the other bolts are in place. Alter-
nately and progressively tighten the bolts to pull the end
cover  and  other components  into  place  with  a final
torque of 45 to 55 ft–lb (6.2 to 7.6 kg–m) (Fig. 85).
Figure 85
IMPORTANT: Make sure springs  (28), shuttle valve
(29),
(24)
and ball  (30) are installed  into the end  cover
in the same position noted during disassembly.
22.
Install plug  (26) that  is not  matched marked  and
new O–ring  (27) into shuttle  port that is  not matched
marked. Install springs (28), shuttle valve (29), and ball
(30)
into open  shuttle port. Install remaining  plug and
new O–ring.
Sand Pro 2020/3020/5020
Page 4 – 69
Hydraulic System (Rev. A)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 170 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website