Toro 98957SL Rev B Sand Pro 2020 3020 5020 Service Manual

Front Fork (SP 5020)
Removal (Fig. 20)
2
1
5
4
NOTE:  If disassembly of the front fork and its bearings
is required, proceed as follows:
6
WARNING
6
5
4
Before jacking upthemachine,reviewandfollow
Jacking Instructions in Chapter 1 – Safety.
1.
Jack up front wheel enough to allow removal of the
front fork.
3
2.
Remove fuel tank from the machine (see Fuel Tank
Removal in Chapter 3 – Briggs & Stratton Vanguard En-
gines).
7
3.
Remove cotter  pin securing the  slotted nut to the
fork shaft. Unscrew slotted nut from the shaft. Remove
steering washer from the shaft.
Figure 20
5.
6.
7.
1.
2.
3.
4.
Cotter pin
Slotted nut
Front fork
Bearing cone
Bearing cup
Grease fitting
4.
Pull fork  from  the frame.  Remove upper  bearing
Steering washers
cone from the frame.
3.
bearing cups into the frame.
If bearing cones or cups were damaged, press new
5.
move steering chain from the front fork and the sprocket
(Fig. 19).
Remove lock  nut  from each  adjustment pin.  Re-
4.
Install steering washers onto the shaft of the front
fork.
6.
Remove front wheel from the  front fork (see Front
Wheel Removal).
5.
If bearing  cones were  damaged  or bearing  cups
were replaced, install new bearing cone onto the shaft
with a bearing driver.
CAUTION
6.
Position fork shaft up through frame. If bearing con-
es were damaged or bearing cups were replaced, install
new bearing cone onto shaft. Install remaining bearing
cone and steering washer onto the shaft.
Support front fork to prevent its falling during re-
moval. Personal injury or damage to the fork may
result from improper handling.
7.
Tighten slotted nut onto shaft until a slight drag is felt
NOTE:  If it is necessary to pry the fork from the frame,
make sure even pressure is  apply to both sides of the
fork to prevent damaging the bearing cone and cup.
when rotating the fork. Back off nut so nearest slot aligns
with cross hole in the shaft. Secure nut to shaft with cot-
ter pin.
7.
place bearings if necessary.
Inspect bearing  cups and cones for  damage. Re-
8.
Installation).
Install front wheel to the front fork (see Front Wheel
8.
from the front fork if necessary.
The chain bracket and chain guide may be removed
9.
Position  steering chain  around  the sprocket  and
chain guide. Secure chain to chain bracket with steering
adjustment pins  and lock  nuts.  Adjust steering  chain
(see Adjust Steering Chain).
Installation (Fig. 20)
1.
fork with cap screws, spacers, and hex nuts.
Secure chain guide and fork stay plate to the front
10.
Installation in Chapter 3 –  Briggs & Stratton Vanguard
Engines).
Install  fuel  tank to  the  machine  (see  Fuel  Tank
2.
Secure chain  bracket to the  chain guide with cap
screws and lock washers.
Wheels, Brakes, and Miscellaneous
Page 6 – 22
Sand Pro 2020/3020/5020
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 170 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website