Toro 98957SL Rev B Sand Pro 2020 3020 5020 Service Manual

10.
Disconnect red positive cable cable (solenoid) from
the starter (Fig. 47).
11.
Remove  lock nut  and  cap screw  securing  black
1
ground wire and black battery cable (negative) to the en-
gine block. Pull cable and  harness clear of the engine
(Fig. 47).
2
12.
securing the engine to its base.
Remove remaining three lock nuts and cap screws
5
4
3
CAUTION
Figure 47
1.
2.
3.
Positive cable (solenoid)
Starter
Lock nut and cap screw
4.
5.
Battery cable (negative)
Ground wire (frame)
Before jacking upthemachine,reviewandfollow
Jacking Instructions in Chapter 1 – Safety.
One person  should  operate the  jack while  the
other person guides  the engine from the  frame
and engine base.
3
IMPORTANT: Make sure  not to damage wires, wire
harness, hoses, and cables while removing the en-
gine from the machine.
2
13.
Remove engine as follows (Fig. 43 and 48):
4
1
1
A.  Positiona jack under the rear of the engine base.
B.  Support engine  with a  jack, then  remove cap
screws and flat washers  securing the engine sup-
port to the frame.
Figure 48
1.
2.
Cap screw & flat washer
Engine support
3.
4.
Traverse rod
Engine base
IMPORTANT: When  the rear of  the engine base  is
lowered,  the  base  will  pivot  at  the front  engine
mounts. Lower base about 1 inch (2.5 cm), which is
enough to allow the top of the engine to clear the tra-
verse rod. Avoid damaging the  cooling fan and oil
cooler  as  the   hydrostat  pivots  up.  The   engine
should then slide off the base. Do not allow engine
to drop.
1.
Install engine to its base as follows (Fig. 43 and 48):
A.  Attach a jack to the rear of the engine base.
B.  Make sure  square key is  placed on  the shaft.
Position engine onto the engine base. Slide engine
shaft into the engine hub
C. Lower rear of the engine base. Remove engine
from the engine hub and base. Remove square key
from the engine shaft.
C. Insert  three  cap screws  through  engine base
andengineblock.Installlocknutstothecapscrews.
Do not tighten fasteners at this time.
14.
cooling fan from damaging the oil cooler.
Secure engine  base and hydrostat to  prevent the
D. Insert  cap screw through engine  base and en-
gine block.  Connect black ground  wire and  black
battery cable  (negative) to  the cap  screw. Screw
lock nut onto the cap screw (Fig. 47).
Engine Installation (Fig. 43)
E.  Tighten all four fasteners securing the engine to
its base.
CAUTION
F.  Jack up engine  base enough to secure the en-
gine support to the frame. Secure engine support to
the frame cap screws and flat washer.
One person  should  operate the  jack while  the
other person guides the engine into the frame.
2.
starter (Fig. 47).
Connect red positive cable  cable (solenoid) to the
IMPORTANT: Make sure not to damage the engine,
fuel and hydraulic lines, electrical harness, or other
parts while installing the engine.
Engine
Sand Pro 2020/3020/5020
Page 3 – 28
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 170 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website