Toro 98957SL Rev B Sand Pro 2020 3020 5020 Service Manual

5.
Disconnect air hose from  the air cleaner. Remove
lower shroud from the cooler mount to prevent damage
to the fan when removing the hydrostat.
1
2
6.
Disconnect control rod from pump lever  and wires
3
from the neutral switch (Fig. 36).
4
7.
Loosen both set screws (11) on the pump hub (19)
enough to allow the hydrostat shaft to be released.
8.
Clamp hydraulic hose (35) and hydraulic hose (25)
to prevent  draining of the  tank. Disconnect all  six hy-
draulic hoses from fittings on the hydrostat. Allow hoses
to drain into a suitable container.
Figure 34
1.
2.
Blue wire (magneto)
3.
Voltage regulator
Red/white wire
Blue wire (voltage reg.)
4.
9.
Remove self tapping screw securing R–clamp and
fuel hose to the frame (Fig. 37)
CAUTION
1
One person should operate the chain fall or hoist
while the  other person guides  the engine from
the frame.
2
3
IMPORTANT: When moving the engine and hydros-
tat from the  frame, make sure not the  damage the
cooling fan, wires, hoses, and cables.
5
4
10.
Reposition hydrostat and engine as follows:
Figure 35
A.  Position a jack or chain  fall to the engine base
(Fig. 39).
1.
2.
3.
Positive cable (solenoid)
4.
5.
Battery cable (negative)
Ground wire (frame)
Starter
Lock nut and cap screw
B.  Remove lock nuts, flat washers, and cap screws
securing  both front  engine mounts  to  the frame
(Fig. 38).
4
2
C. Remove  cap screws and flat washers securing
the engine support the the frame (Fig. 39).
3
D. Lower and pull back hydrostat and engine from
the cooler mount so  the cooling fan is clear of the
mount.
5
11.
Separate hydrostat from the engine base by remov-
1
ing both lock nuts and socket head screws.
Figure 36
4.
5.
12.
woodruff key (9) from the hydrostat shaft.
Remove  fan hub  (27)  with  cooling fan  (28)  and
1.
2.
3.
Control rod
Pump lever
Wires
Neutral switch
Pump plate
13.
Match mark position of  all hydraulic fittings on the
hydrostat.  Remove all  hydraulic  fittings and  O–rings
from the hydrostat. Plug or cap all ports to prevent con-
tamination.
Installation (Fig. 33)
1.
Make sure hydraulic hoses, fittings, and  tubes are
cleaned thoroughly.
14.
Remove cap screw and lock nut securing the pump
2.
screws. Secure  pump lever  to the  hydrostat trunnion
with cap screw and lock nut (Fig. 36).
Securing pump plate to the hydrostat with three cap
lever  to  the  hydrostat  trunnion.  Remove  three  cap
screws securing the pump plate to  the hydrostat while
pulling the pump plate from the hydrostat (Fig. 36).
Sand Pro 2020/3020/5020
Page 4 – 45
Hydraulic System (Rev. A)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 170 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website