Toro 10178SL Service Manual Groundsmaster 4300 D Preface Publication

NOTE:  Traction pump and  gear pump  should be re-
moved from machine as an  assembly. Once removed
from machine, pumps can be separated for service.
3
Removal (Fig. 67)
1.
brake, lower  cutting decks and  stop engine. Remove
key from the ignition switch.
Park themachine onalevelsurface,  engage parking
2
1
2.
Installing Hydraulic System Components at the begin-
ning of the Service and Repairs section of this chapter.
Read the  General Precautions  for Removing  and
Figure 68
1.
2.
Piston (traction) pump
Gear pump
3.
Traction cable bracket
CAUTION
Before opening hydraulic system, operate all hy-
draulic controls to relieve system pressure and
avoid injury from pressurized hydraulic oil. See
Relieving Hydraulic System Pressure in the Gen-
eral Information section of this chapter.
4
7
12
2
11
10
9
8
8
13
14
3.
thoroughly clean traction and gear pump assembly and
all hydraulic connections.
To prevent contamination  of the hydraulic  system,
4.
Label hydraulic hoses to assist in assembly. Discon-
nect all hydraulic hoses and tubes  from fittings on the
traction and gear pump assembly. Allow hydraulic lines
to drain into a suitable container. Plug or cap openings
of pumps and lines to prevent contamination.
1
1
2
7
5.
Pump Drive Shaft Removal in this section).
Remove hydraulic pump drive shaft (see Hydraulic
4
5
6
3
6.
Separate  traction  cable   assembly  from  traction
Figure 69
pump (Fig. 69):
1.
2.
3.
4.
5.
6.
7.
Cap screw (2 used)
Flange nut (2 used)
Traction cable
Flange nut (2 used)
Flange screw (2 used)
Traction cable bracket
Cap screw (2 used)
8.
9.
Lock nut (2 used)
Flat washer
A.  Removeflangenut(item4inFig.69)thatsecures
lever damper (item  14 in Fig. 69)  to traction cable
bracket.
10. Flat washer
11. Ball joint
12. Traction lever bracket
13. Cap screw
14. Lever damper
B.  Remove cap screws (items 7 and 13 in Fig. 69)
and lock nut(item 8in Fig. 69) that secure traction le-
ver bracket (item 12 in Fig. 69) to pump lever.
CAUTION
C. Loosen  jam nuts  that  secure traction  cable to
traction cable bracket (item 6 in Fig. 69).
Make  sure  lift or  hoist  can  support  the  total
weight of the  pump assembly before removing
the cap  screws  from the  pump assembly  and
frame. Pump assembly weighs approximately 67
pounds (30.5 kg).
D. Position   traction  cable  assembly   away  from
pump assembly.
7.
traction neutral switch and position harness away from
transmission.
Disconnect wire harness  electrical connector from
8.
Connect alift or hoist to hole intraction cable bracket
on traction  pump to  support pump assembly  and for
pump removal.
Groundsmaster 4300--D
Page 4 -- 69
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 255 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website