Toro 10178SL Service Manual Groundsmaster 4300 D Preface Publication

IMPORTANT: When capping lift cylinder fitting and
hydraulic hose end, use a steel cap and plug to en-
sure that fluid leakage will not occur. Plastic plugs
will not hold hydraulic pressure that will  be devel-
oped during this test procedure.
3
2
4.
Place a steel cap  on the open lift cylinder fitting to
seal the lift cylinder. Also, install a steel plug in the open
endofthedisconnected  hosetopreventleakage   orcon-
tamination.
1
5.
Slowly lower the jack and remove it from under the
lift arm. The cutting deck should settle slightly and then
be supported by the capped lift cylinder.
6.
der head with a piece of tape (Fig. 57).
Markthepositionoftheliftcylinderrodattheliftcylin-
Figure 56
1.
2.
Lift cylinder (#5 shown)
Cylinder rod end fitting
3.
Hydraulic hose
7.
Leave the  machine parked  for two  (2) hours  and
monitor the lift cylinder. The weight of the cutting deck
may cause the lift cylinder to gradually extend. Use the
tape location  to determine lift  cylinder rod movement
(Fig. 58).
1
A.  If lift cylinder rod movement is  less than 1.250”
(31.7
mm)aftertwo(2)hours,makesurethatthecut-
ting deck has not settled to the ground. If the cutting
deck is still suspended after two (2) hours and lift cyl-
inder rod movement is less than 1.250” (31.7 mm),
consider that the lift cylinder is in good condition. A
cylinder in good, usable condition will show minimal
movement.
3
2
B.  Rod movement in excess of 1.250” (31.7 mm) af-
ter two (2) hours indicates that the lift cylinder may
have internal seal damage  or excessive wear. Re-
move and inspect the lift cylinder (see Lift Cylinder
and Lift Cylinder Service in the Service and Repairs
section of this chapter).
Figure 57
1.
2.
Lift cylinder rod
Lift cylinder head
3.
Tape (initial position)
8.
Once lift  cylinder condition  has been  determined,
use a jack to raise the lift arm slightly which will remove
the load from the lift cylinder. Leave the jack to support
the lift arm and to prevent it from lowering. Remove the
cap from the cylinder  fitting and the plug from the  hy-
draulic hose. Connect the hydraulic hose to the lift cylin-
der fitting.
2
9.
Carefully remove jack from under the lift arm. Start
engine and operate lift cylinders through several up and
down cycles. Stop the engine and check  for any leak-
age.
1
10.If
inders.
needed, repeat steps 2 through 10 for other lift cyl-
Figure 58
1.
Tape (after 2 hours)
2.
Cylinder rod movement
11.
After testing is complete, check oil level in hydraulic
reservoir and adjust if necessary.
Groundsmaster 4300--D
Page 4 -- 55
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 255 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website